elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя | Manualshive

Страница: 13 / 68

background image

11

Addressing the equipment

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

2.4.1. Information on cavity wall mounting

2.5. Notes on mounting and commissioning

Never expose the device to water (e.g. rain) or dust. This can damage the electronics.
You must not exceed a relative humidity of 95%. Avoid condensation.

The air slots on the side must not be closed or covered. The device must not be painted
over.

After the bus voltage has been applied, the device will enter an initialisation phase last-
ing a few seconds. During this phase no information can be received or sent via the
bus.

The motion sensor has a start-up phase of approx. 15 seconds during which no motion
detection takes place.

3.

Addressing the equipment

The equipment is delivered with the bus address 15.15.255. You can program a differ-
ent address in the ETS by overwriting the address or by teaching the device via the pro-
gramming button.

The programming button is on the inside of the housing (Fig. 3: No. 3).

4.

Maintenance

The movement sensor and the air slots on the side must not get dirty or covered. As a
rule, it is sufficient to wipe the device with a soft, dry cloth twice a year.

Fig. 8

Close the housing by positioning the cover and
snapping it into place.

Fig. 9

For

cavity wall mounting

, use a wall light junction

box. In this case, screw the base on the box with
only one screw.

«
...
11
12
13
14
15
...
»

Содержание Mini-Sewi KNX L-Pr





































































Отзывы:

Нет отзывов

Похожие инструкции для Mini-Sewi KNX L-Pr

Security Camera

Бренд: Raritan Страницы: 2

Бренд: Data Harvest Страницы: 19

Security Camera

Бренд: TANDBERG Страницы: 247

Бренд: X10 Страницы: 4

Бренд: Dahua Страницы: 16

Бренд: HIKVISION Страницы: 39

MEMCO Elite 618

Бренд: Halma Страницы: 4

SUCCESS ATP-434N

Бренд: TECHNO-AC Страницы: 21

Бренд: Huviron Страницы: 2

Caregiver CAS-FAM

Бренд: Secure Страницы: 3

FHF DSLB 20 LED

Бренд: Eaton Страницы: 28

SpectrAlert S1224MCW

Бренд: System Sensor Страницы: 4

Бренд: Paradox Страницы: 2

Vantage MCB7041

Бренд: Lorex Страницы: 2

Бренд: Mini Gadgets Страницы: 18

Бренд: SensoIRIS Страницы: 2

Бренд: Vivotek Страницы: 4

Бренд: Abus Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды