elsner elektronik Mini-Sewi KNX L-Pr страница 46 Скачать руководство пользователя | Manualshive

Страница: 46 / 68

background image

44

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

When using the control variable for a 4/6 way valve, the following applies:
0%...100% heating = 66%...100% control variable
OFF = 50% control variable
0%...100% cooling = 33%...0% control variable

6.9.1. Heating control level 1/2

If a heating control mode is configured, one or two setting sections for the heating le-
vels are displayed.

In the 1st level, heating is controlled by a PI control, which allows to either enter control
parameters or select predetermined applications.

In the 2nd level (therefore only in case of 2-level heating), heating is controlled via a PI
or a 2-point-control.
In level 2, the setpoint difference between the two levels must also be specified, i.e. be-
low which setpoint deviation the second level is added.

PI control with control parameters:

This setting allows individual input of the parameters for PI control.

Specify the deviation from the setpoint value at which the maximum control variable
value is reached, i.e. the point at which maximum heating power is activated.
The reset time shows how quickly the controller responds to deviations from the set-
point value. In case of a short reset time, the control responds with a fast increase of
the control variable. In case of a long reset time, the control responds somewhat less

Control type

(for level 2 only)

• 2-point-control
• PI control

Control variable of the 2nd Level is on

(only for level 2 with 2 point controlling)

• 1 bit object
• 8 bit object

Setpoint difference between 1st and 2nd
level (in 0.1°C)

(for level 2)

0...100; 40

Control type

(for level 2, no common control variables)

• 2-point-control
• PI control

Control variable is a

(for level 2 with 2-point controlling, no
common control variables)

• 1 bit object
• 8 bit object

Control type

•

PI control

Setting of the controller by

•

Controller parameter

• specified applications

«
...
44
45
46
47
48
...
»

Содержание Mini-Sewi KNX L-Pr





































































Отзывы:

Нет отзывов

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренд: D-Link Страницы: 44

Бренд: Ziginte Страницы: 18

Бренд: Datalogic Страницы: 7

Бренд: EDELRID Страницы: 52

Бренд: Q-See Страницы: 1

Бренд: Saferhomee Страницы: 8

Бренд: Europlex Страницы: 15

Бренд: Super Circuits Страницы: 28

ClareOne CLR-C1-CO

Бренд: clare Страницы: 11

Бренд: BUCKINGHAM MFG Страницы: 2

Бренд: IntelliCam Страницы: 11

Бренд: Sennco Solutions Страницы: 23

Бренд: TP-Link Страницы: 40

Бренд: Brilix Страницы: 37

Бренд: Vivotek Страницы: 12

Бренд: Maxouttech Страницы: 3

Бренд: Enviro Страницы: 98

ELI-ACVI-PTZ13-12X

Бренд: e-Line Technology Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды