elsner elektronik Mini-Sewi KNX L-Pr страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 68

background image

36

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

The

minimum and maximum readings

can be saved and sent to the bus. Use the

"Reset temperature min/max. value" objects to reset the values to the current readings.
The values are not retained after a reset.

6.8.

Temperature threshold values

The chapter "Temperature threshold values" only applies to the TH-L-
Pr model.

Activate the required temperature threshold values. The menus for setting the th-
reshold values are displayed.

6.8.1. Threshold value 1, 2, 3, 4

Threshold value

Set, in which cases

threshold values and delay times

received via object are to be

retained. The parameter is only taken into consideration if the setting via object is ac-
tivated below. Please note that the setting "After power supply restoration and pro-
gramming" should not be used for the initial start-up, as the factory settings are always
used until the first communication (setting via objects is ignored).

Set the threshold value directly in the application program using parameters, or define
them via the bus using a communication object.

Threshold value setting via parameter:

Set the threshold values and hysteresis directly.

Threshold value setting via a communication object:

Define, how the threshold value is to be received from the bus. Basically, a new value
can be received, or simply a command to increase or decrease.

During initial commissioning, a threshold value must be defined, which will be valid
until the first communication with a new threshold value. For units which have already
been taken into service, the last communicated threshold value can be used. Basically,

Use minimum and maximum value

No • Yes

Use threshold value 1/2/3/4

Yes • No

Maintain the

threshold values and delays received via
communication objects

• never
• after power supply restoration
• after power supply restoration and
programming

Threshold value setting via

Parameter

• Communication objects

Threshold value in 0.1°C

-300 … 800; 200

«
...
36
37
38
39
40
...
»

Содержание Mini-Sewi KNX L-Pr





































































Отзывы:

Нет отзывов

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренд: D-Link Страницы: 16

Бренд: jablotron Страницы: 16

Бренд: Salus Страницы: 2

Бренд: Abus Страницы: 2

Бренд: Vanderbilt Страницы: 4

Бренд: Panasonic Страницы: 228

Бренд: Vertiv Страницы: 16

Бренд: V-TAC Страницы: 9

IQ PANEL 2 PLUS

Бренд: QOLSYS Страницы: 2

Бренд: Olympia Страницы: 40

Бренд: IDTECK Страницы: 57

Бренд: Verint Страницы: 16

Бренд: Wisenet Страницы: 2

Бренд: dallmeier Страницы: 40

Бренд: Abus Страницы: 61

Бренд: Magellan Страницы: 2

Бренд: Dahua Technology Страницы: 15

Бренд: Ubiquiti Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды