elsner elektronik Intra-Sewi KNX L-Pr Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 69

background image

37

Parameter setting

Sensors Intra-Sewi KNX TH-L-Pr and Intra-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

In addition, you can refer to a

slave signal

, i.e. a signal from an additional motion de-

tector, for controlling purposes.

The slave device periodically sends a 1 to the bus, as long as a motion is detected. The
master receives this at the input object "master: slave message" and evaluates the sla-
ve message as an own sensor message.

Furthermore, the master has the possibility of triggering a reset of the slave sending
cycle.

Information on setting the slave sending cycle and the cycle reset can
be found in chapter

Align communication between master and slave

Set the

object type and value

for the master's slave cycle reset output in the same

way, as the cycle reset input for the slave.

The master can be

blocked

via the bus.

5.6.2. Align communication between master and slave

Sending cycle slave - switch-off delay master

Set the slave's

sending cycle

shorter than the master's switch-off delay. Thereby it is

ensured that the master does not perform a switch-off action, while the slave is still de-
tecting a motion.

Slave cycle reset

The cycle reset for the slave is required, if a master switch action by the "master: central
off" object was triggered.

When the master performs a switch-off action, it simultaneously sends a message to
the bus via the "master: slave cycle reset". . This message can be received by the slave

Use slave signal

No • Yes

Slave cycle reset object type

• 1 bit
• 1 byte (0%...100%)

Cycle reset at value

0 • 1 and/or 0...100; 1

Use block

No •

Yes

Analysis of the blocking object

• at value 1: block | at value 0: release
• at value 0: block | at value 1: release

Value prior to first communication

0 • 1

Output pattern

On block

• do not send anything
• Send value

For release

• as for transmission pattern
• send current value immediately

«
...
35
36
37
38
39
...
»

Содержание Intra-Sewi KNX L-Pr






































































Отзывы:

Нет отзывов

Похожие инструкции для Intra-Sewi KNX L-Pr

Бренд: A.E.B. Страницы: 16

WV-CP500 series

Бренд: Panasonic Страницы: 2

Бренд: Gamewell Страницы: 21

Бренд: U-Prox Страницы: 29

Бренд: StarVedia Страницы: 2

NEXT PLUS Series

Бренд: Visonic Страницы: 4

Бренд: Inovonics Страницы: 4

Бренд: INIM Страницы: 4

Бренд: Vivotek Страницы: 2

Бренд: Somogyi Страницы: 25

theRonda S360-100 DE GR

Бренд: Theben Страницы: 6

Бренд: Intellinet Страницы: 11

Бренд: SALUPO Страницы: 12

AlertMaxx DMS-269

Бренд: Delta Страницы: 16

UniFi UVC-G4-PRO

Бренд: Ubiquiti Страницы: 33

D5004FH+C1030DP7*4

Бренд: Winbook Страницы: 81

Бренд: SHARX SECURITY Страницы: 11

Бренд: Hanwha Vision Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды