ELNA eXcellence 780 Скачать руководство пользователя | Manualshive

Страница: 37 / 43

background image

35

Mechanical adjustment

Presser foot lifter stopper position (1)

The distance between the presser foot spring release base and the presser foot lifter should be in the range of 39.4
mm to 39.8 mm when the presser foot is raised with the presser foot lifter.

Preparation:
1. Turn the power switch ON. Press the presser foot lifter

button to lower the presser foot. Turn the power switch
OFF.

2. Raise the presser foot with the presser foot lifter.

3. Remove the top cover (see page 2).

39.4 to 39.8 mm

Presser foot lifter stopper

Presser foot spring

release base

Setscrew B

Setscrew F

Setscrew A

Carrying handle
supporter (front)

Setscrew D

LED cover
(unit)

4.  Disconnect the connector from the face cover.
    Loosen the setscrew A.
    Remove the setscrews B and C.
    Remove the carryin handle supporter (front).

Needle bar
supporter spring

5.  Remove the setscrew D and the LED cover (unit).
    Remove the needle bar supporter spring.
    Loosen the setscrew E.
    Remove the setscrews F and G.
    Remove the front bracket (unit).

Front bracket (unit)

Setscrew C

Connector

Setscrew G

Setscrew E

View from

the front side

«
...
35
36
37
38
39
...
»

Содержание eXcellence 780












































Отзывы:

Нет отзывов

Похожие инструкции для eXcellence 780

KM 130/300 R Bp

Бренд: Kärcher Страницы: 372

Бренд: Kärcher Страницы: 16

BRC 30/15 C *JP

Бренд: Kärcher Страницы: 48

KM 130/300 R Bp

Бренд: Kärcher Страницы: 27

Бренд: Kärcher Страницы: 11

Бренд: Kärcher Страницы: 16

Бренд: Kärcher Страницы: 4

Бренд: Panasonic Страницы: 88

Бренд: Republic Bank Страницы: 18

CoverPro 1000CP

Бренд: Janome Страницы: 21

CONTOUR 350 DELUXE

Бренд: H. Winter Страницы: 23

Бренд: MyBinding Страницы: 3

Бренд: GBC Страницы: 4

Autopax PAX200H

Бренд: Quasar Страницы: 76

Бренд: A-S-S Страницы: 13

Бренд: Fellowes Страницы: 7

Smoke 700 Magic

Бренд: Audibax Страницы: 2

ULTRAFEED 120931

Бренд: Sailrite Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды