ELNA eXcellence 780 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 43

background image

32

Setscrew

⇔

Hexagonal
socket screw

Mechanical adjustment

Buttonhole lever

Buttonhole

lever guide

Buttonhole lever

Buttonhole

lever guide

Setscrew

Hexagonal socket screw

1.6 mm

Slider

Stopper

Buttonhole foot (R)

1. Turn the power switch ON while pressing the Start/

Stop button and the Reverse stitch button. The LCD
shows the Factory Setting Mode. Press “BH Sensor”
key.

2. Open the face cover. Lower the Buttonhole lever.

Loosen the setscrew on the buttonhole lever guide.
Move the buttonhole lever guide to the left to adjust
the position. Tighten the setscrew when the indication
below "BH Sen" changes from “H” to “L”.

3. Attach the automatic buttonhole foot (R). Insert a 1.6

mm thick spacer between the stopper and slider of the
foot.

4. Press the presser foot lifter button to lower the

automatic buttonhole foot (R). Lower the buttonhole
lever.

5. Turn the hexagonal socket screw counterclockwise (use

an Allen wrench of 2 mm width across flats) until the
indication below "BH Sen" shows “H”.

Turn the setscrew slowly clockwise until the indication

changes to "L".

«
...
32
33
34
35
36
...
»

Содержание eXcellence 780












































Отзывы:

Нет отзывов

Похожие инструкции для eXcellence 780

Бренд: Nilfisk-ALTO Страницы: 84

Zero Pulsar Plus 55-S

Бренд: Clemco Страницы: 47

Бренд: Singer Страницы: 8

Бренд: White Страницы: 44

Бренд: Ultratec Страницы: 7

Memory Craft 550E

Бренд: Janome Страницы: 84

Бренд: Janome Страницы: 96

Бренд: Consew Страницы: 54

Бренд: Duerkopp Adler Страницы: 38

IP PHONEFAX 49A

Бренд: Sagem Страницы: 56

Бренд: Advance acoustic Страницы: 40

Fitness E-ST 5090

Бренд: Star Trac Страницы: 28

Бренд: JUKI Страницы: 116

Бренд: morse Страницы: 9

Бренд: Bosch Страницы: 17

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 52

Бренд: Bosch Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды