SETTING CLOCK – ALL MODELS
Setting clock initially or after power failure (if control is
flashing)
1. To set time: Touch UP or DOWN button until correct
time is shown.
Resetting time (if control is not flashing)
2. Push SELECT 5 times until CLOCK light is
illuminated. Push UP or DOWN until correct time is
shown.
NOTE: You must act within 3 seconds or the function you
are trying to set will cancel.
SETTING MINUTE TIMER:
1. Touch SELECT once. 00:00 will appear. Within
3 seconds press UP for time in minutes.
BAKE OR BROIL
Turn Selector switch to bake or broil. Set oven thermostat
to desired temperature.
Preheating oven
on bake normally takes about 15 minutes,
indicator cycle light will go out when oven has reached
temperature. The Broiler takes about 3 minutes to preheat.
After preheating, broiler may be set to variable tempera-
tures by adjusting the thermostat.
DELAYED BAKE
(Oven turns on and off automatically:
1. Touch SELECT 2 times. Current time will flash. Press
UP until the correct START TIME has been reached.
Wait 3 seconds. Touch SELECT once. COOKTIME
will appear. Press UP until the proper cooktime has
been reached. Set the oven selector to AUTO and
thermostat to the correct temperature.
19
27
Replace Oven Bake Burner Cover
1.
Align notches on the oven bake burner cover with shoulder
screws in the bottom of the oven.
2.
Lower cover, and slide to left or right to slide shoulder screws
into the narrow ends of the notches, then lock into place.
Convert Oven Broil Burner (30" [76.2 cm] and 36"
[91.4 cm] models and the right oven cavity on 48"
[121.9 cm] models)
1.
Using a 1/4" (6.4 mm) nut driver, remove broil burner screw.
Set aside with side igniter positioned on the right.
2.
Pull the broil burner toward you until it slides out of the hole in
the oven back, and pull the electrode out of the bracket. The
broil burner will hang down in the back of the oven while you
change the orifice.
3.
Apply masking tape to the end of a 7 mm nut driver to help hold
the gas orifice spud in the nut driver while changing
it. Insert
nut driver into the gas opening, and press down onto
the gas
orifice spud, then remove by turning the orifice spud
counterclockwise and lifting out. Set
natural
gas
orifice spud
aside.
4.
Natural gas orifice spuds are stamped with a letter and a
number. Install the Number 148 oven broil burner orifice spud.
5.
Place Propane gas orifice in plastic parts bag for future use,
and keep with package containing literature.
6.
Replace the broil burner in the hole in the oven back with the
broil burner assembly inside the broil burner electrode hole as
illustrated.
7.
Reinstall the oven broil burner screw. See Step 1 for
illustration. The screw is aligned with the hole when
a click sounds.
B
A
B
A
A. Cover notches (4)
B. Shoulder screws (4)
A
A. Bake burner cover
B
A
C
A. Broil burner screw
B. Broil burner
C. Broil burner orifice hole
A
B
A. Grasp electrode here.
B. Bracket
Broil burner hanging
in back of oven
A
B
C
A. Oven back
B. Broil burner orifice
C. Broil burner orifice hole
A
B
C
A. Broil burner orifice hole
B. Broil burner electrode
C. Broil burner electrode hole
27
Replace Oven Bake Burner Cover
1.
Align notches on the oven bake burner cover with shoulder
screws in the bottom of the oven.
2.
Lower cover, and slide to left or right to slide shoulder screws
into the narrow ends of the notches, then lock into place.
Convert Oven Broil Burner (30" [76.2 cm] and 36"
[91.4 cm] models and the right oven cavity on 48"
[121.9 cm] models)
1.
Using a 1/4" (6.4 mm) nut driver, remove broil burner screw.
Set aside with side igniter positioned on the right.
2.
Pull the broil burner toward you until it slides out of the hole in
the oven back, and pull the electrode out of the bracket. The
broil burner will hang down in the back of the oven while you
change the orifice.
3.
Apply masking tape to the end of a 7 mm nut driver to help hold
the gas orifice spud in the nut driver while changing
it. Insert
nut driver into the gas opening, and press down onto
the gas
orifice spud, then remove by turning the orifice spud
counterclockwise and lifting out. Set
natural
gas
orifice spud
aside.
4.
Natural gas orifice spuds are stamped with a letter and a
number. Install the Number 148 oven broil burner orifice spud.
5.
Place Propane gas orifice in plastic parts bag for future use,
and keep with package containing literature.
6.
Replace the broil burner in the hole in the oven back with the
broil burner assembly inside the broil burner electrode hole as
illustrated.
7.
Reinstall the oven broil burner screw. See Step 1 for
illustration. The screw is aligned with the hole when
a click sounds.
B
A
B
A
A. Cover notches (4)
B. Shoulder screws (4)
A
A. Bake burner cover
B
A
C
A. Broil burner screw
B. Broil burner
C. Broil burner orifice hole
A
B
A. Grasp electrode here.
B. Bracket
Broil burner hanging
in back of oven
A
B
C
A. Oven back
B. Broil burner orifice
C. Broil burner orifice hole
A
B
C
A. Broil burner orifice hole
B. Broil burner electrode
C. Broil burner electrode hole
27
Replace Oven Bake Burner Cover
1.
Align notches on the oven bake burner cover with shoulder
screws in the bottom of the oven.
2.
Lower cover, and slide to left or right to slide shoulder screws
into the narrow ends of the notches, then lock into place.
Convert Oven Broil Burner (30" [76.2 cm] and 36"
[91.4 cm] models and the right oven cavity on 48"
[121.9 cm] models)
1.
Using a 1/4" (6.4 mm) nut driver, remove broil burner screw.
Set aside with side igniter positioned on the right.
2.
Pull the broil burner toward you until it slides out of the hole in
the oven back, and pull the electrode out of the bracket. The
broil burner will hang down in the back of the oven while you
change the orifice.
3.
Apply masking tape to the end of a 7 mm nut driver to help hold
the gas orifice spud in the nut driver while changing
it. Insert
nut driver into the gas opening, and press down onto
the gas
orifice spud, then remove by turning the orifice spud
counterclockwise and lifting out. Set
natural
gas
orifice spud
aside.
4.
Natural gas orifice spuds are stamped with a letter and a
number. Install the Number 148 oven broil burner orifice spud.
5.
Place Propane gas orifice in plastic parts bag for future use,
and keep with package containing literature.
6.
Replace the broil burner in the hole in the oven back with the
broil burner assembly inside the broil burner electrode hole as
illustrated.
7.
Reinstall the oven broil burner screw. See Step 1 for
illustration. The screw is aligned with the hole when
a click sounds.
B
A
B
A
A. Cover notches (4)
B. Shoulder screws (4)
A
A. Bake burner cover
B
A
C
A. Broil burner screw
B. Broil burner
C. Broil burner orifice hole
A
B
A. Grasp electrode here.
B. Bracket
Broil burner hanging
in back of oven
A
B
C
A. Oven back
B. Broil burner orifice
C. Broil burner orifice hole
A
B
C
A. Broil burner orifice hole
B. Broil burner electrode
C. Broil burner electrode hole
