background image

11

USER MANUAL

Inteli-Mixer RM-2

Troubleshooting

Problem description

Possible causes

Possible solutions

While vortexing rack is shifted 
from given position.

Vortexing frequency is too high 
for current rack loading

.

Reduce vortexing frequency by adjust-
ing vortexing programs PU & Pu

Rack is not rotating or is 
rotating not accordingly to set 
program.

There is a mechanical obstacle 
for rack movement.

Find and remove an obstacle.

The machine does not work 
accordingly to the set pro-
gram.

Program is entered incorrectly.

Carefully examine programming man-
ual once again and try to re-enter the 
program.

Program does not contain posi-
tion correction

Recompose the program entering 
position correction function.

While programming the 
machine exited programming 
mode automatically. 

Program length of 78 steps is 
exceeded.

Try to reduce the length of a program.

Custom programs C1, C2 or 
C3 perform simple rotation.

Program memory is empty.

Enter a new custom program. (See 
creating custom programs).

Disinfection and cleaning

Before you start disinfection or cleaning make sure 
the power adapter is unplugged. It is recommended 
to perform cleaning with water and universal wash-

ing liquids. Afterwards the machine should be care-
fully dried.

Safety features

It is prohibited to: 
•  Plug the machine in to a power outlet with con-

figuration which differs from the power adapt-

ers’ plug configuration.

•  Plug the power adapter in to the outlet if the 

adapter is damaged.

Transportation and storage

To insure safety during the transportation, trans-
ported equipment should be packed in the original 
manufacturers’ packaging or similar packaging sub-
stitute.
Equipment can be transported by any kind of 
closed transport so that equipment is tightly fixed 
and transportation runs accordingly to regulations 
applied to this way of transport.

Equipment should be stored in original manufactur-
ers packaging in dry room with humidity not more 
than 80% and temperature range from +10˚C up to 
+40˚C. 
It is not recommended to store the equipment 
more than 36 month.

Содержание Inteli-Mixer RM-2













Отзывы: