(L)VRCTLDDWSC*A, *2A VRCTLRDDWSC*A, *2A , (L)VRCTL8WSC*1A, *2A, *3A, VRCTLR8WSC*1A, *2A, *3A
Page 6
98982C (Rev. T - 01/19)
Fig. 5
Note: Screw the locknut hand tight to seal
Fig. 6
B
C
A
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A
B
C
BOTTLE FILLER INSTALLATION
1)
Remove wall mounting plates from Coolers.
Install Wall Mounting Plates as per rough-in diagrams on Page 4 or 5 of this instruction.
NOTE: Mounting plates MUST be supported securely. Add fixture support carrier if wall will not provide adequate support.
2)
Install lower water cooler only
at this time onto bracket as per rough-in diagram (See rough-in on Page 4 or 5). DO NOT connect power to cooler at this time or turn water
supply on.
3)
Remove (L)VRCTL Bottle Filler from carton.
Lay Bottle Filler on water cooler basin and cut insulation from tube even with bottom of unit, remove this insulation from the
3/8” tube, but do not discard. Feed the powercord and waterline through the hole on top of water cooler.
NOTE:
To prevent scratching the basin place a towel or soft cloth over the entire basin when working above it.
4)
With the power cord and waterline
on top of water cooler, place Bottle Filler onto mounting bracket on basin. (See Fig. 4). Make sure bottle filler is installed properly on the
basin gasket.
5)
Once Bottle Filler is installed on basin mounting bracket,
tighten the two screws (supplied) one on each side of the bottle filler. Install Top Cover on Bottle Filler (See Fig.
4) with two mounting screws (supplied).
Caution do not over tighten screws.
6)
Secure non-refrigerated unit to wall,
connect drains and water inlet.
7)
Install the 1/4” poly tubing and insulation
from the outlet of the filter to the union on top of the evaporator. Install the 1/4” poly tubing and insulation from the regulator in
the non-refrigerated cooler to one of the tees at the evaporator outlet. Install remaining tube insulation to the water line from bottle filler, connect Bottle Filler waterline inside
of the water cooler by connecting the 3/8” water line to the tee.
8)
For Model LVRCTL Install filter cartridge, remove filter from carton,
remove protective cap, attach filter to filter head by firmly inserting into head and rotating filter
clockwise.
NOTE:
If existing plumbing rough-in locations (Drain, Water In, Electric Supply) do not allow the filter to be mounted inside the cooler cabinet the filter can be installed
horizontally below the unit. A retrofit kit is available to mount the filter beneath the cooler.
9)
Turn water supply on and inspect for leaks.
Fix all leaks before continuing.
10)
Once unit has been inspected for leaks
and any leaks that are found are corrected, plug Bottle Filler and (L)VRCTL unit into wall. Be sure to reinstall fuse to the circuit or
switch the circuit breaker back to the “ON” position.
11)
Once power is applied to Bottle Filler,
the GREEN LED light should illuminate showing good filter status along with the LCD Bottle Counter.
12)
Verify proper dispensing by depressing the button
at the top of the Bottle Filler and verify water dispenses. Note: the first initial dispenses might have air in line which
may cause a sputter. This will be eliminated once all air is purged from the line.
13)
Once unit tests out,
install Lower Panel back on (L)VRCTL water coolers. Unit is now ready for use.
MOUNTING BRACKET
FOR FASTENING UNIT
TO WALL
TOP COVER
MOUNTING
SCREWS
Fig. 4
MOUNTING SCREWS
DO NOT REMOVE
BOTTLE FILLER
WATER COOLER
NOTE: TRIM PLATES MUST BE
INSTALLED ON THE INSIDE
OF THE BOTTLE FILLER
SIDE PANEL SLOTS.