background image

Install framing for hood support 

 
•  If drywall is present, mark the screw hole locations. 

Remove the template. 

•  Cut away enough drywall to  expose 2 vertical studs at 

the holes location indicated by the template. 

 

Install two horizontal supports at least 4" X 2" between 

two wall studs at the bottom  and upper mounting holes 
installation location. 

•  The horizontal support must be flush with the room side 

of the studs. 

 

Use cleats behind both sides of the support to secure to 

wall studs. 

•  Reinstall drywall and refinish. 

IMPORTANT- Framing must be capable of supporting 
100 lbs. 
 

 

  

  

Mounting the hood

 

WARNING:

 2 people are require d to lift and position the 

hood onto the mounting screws. 

•  Place the template on the wall along the horizontal line, 

make sure the template is leveled and centered with the 
centerline. 

•  Mark “upper” screw holes locations in the wall. 
• 

IMPORTANT.

 Check to be sure that hole locations are 

leveled and correctly centered by the vertical centerline. 

•  Drive “upper” wood screws by hand. Leave ¼ “ of 

distance between the screw head and the wall. 

•  Remove the grease filter and mount the hood onto the 

“upper” screws. 

  

  

•  Mark “lower” wood 
       screw holes locations 
       in the wall using a 
       pencil. 

    

•  Remove the hood. 
•  Drive “lower” wood screws, by hand. Remove screws. 
•  Mount the hood onto the “upper” screws. 
•  Drive and tighten the “upper” wood screws, by hand. 
•  Drive and tighten the “lower” wood screws, by hand. 

  

  

Connecting the ductwork

 

•  Install ductwork, making connections in the direction of 

airflow as illustrated. 

•  Push duct over the exhaust outlet. 
•  Wrap all duct joints and the flange connections with duct 

tape for an airtight seal. 

•  Make the same connection in the wall or ceiling vent exit. 

  

  

 

 

Install the 8” round transition as shows the image below.
The installation screws and the 8” round transition are
included on the hood package.

8”

Содержание Lugano ELG636SS




















Отзывы: