ELGA PURELAB Prima 15 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 34

ELGA PURELAB Prima 15 Скачать руководство пользователя страница 24

PURELAB Prima 7/15/30

Operator Manual

ELGA

Page 20

PURELAB Prima 7/15/30 Version 01 09/08

7.1 Replacing the LC140 Pre-treatment Cartridge

The pre-treatment cartridge should be replaced when indicated by the
change reminder.

Step 1 - Switch Unit Off

1. SWITCH the

PURELAB Prima

off at the power

switch at the top left hand side of the unit.

2. ENSURE pressure has dissipated from the unit

by waiting a few minutes after switching off the
power.

Step 2 - Remove Pre-treatment Cartridge

1. OPEN front door.

2. IDENTIFY the pre-treatment cartridge. (LC140).

3. REMOVE the reducing fitting from the elbow at

the bottom of the cartridge, by pushing back the
retaining collet on the push fit connector and
withdrawing the reducer.

4. REMOVE the reducing fitting from the top of the

cartridge.

5. REMOVE exhausted cartridge from retaining

clips and discard.

Note: The consumable is non-hazardous.

Dispose of as ordinary waste,
observing all local and national
regulations.

Step 3 - Replacing the Pre-treatment Cartridge

1. UNPACK new cartridge and remove the two

protective transit plugs sealing the inlet and outlet
connection.

2. SECURE the new cartridge into its retaining clips

ensuring the cartridge is the correct way up.

3. REFIT the reducing fitting from the elbow at the

bottom of the cartridge by pushing the reducer
into the elbow connector until locked and held by
the retaining collet.

4. REFIT the outlet tubing to the top of the cartridge.

5. RESET pre-treatment cartridge timer.

(See

Section 5.4 Setting Up Display and Replacement
Timers)

.

6. PRESS the PROCESS button to start the unit.

7. CHECK the unit for leaks and close front door.

Pre-treatment cartridge

Location of Pre-treatment

Cartridge

«
...
22
23
24
25
26
...
»

Содержание PURELAB Prima 15



































Отзывы:

Нет отзывов