ELGA PURELAB Prima 15 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 34

ELGA PURELAB Prima 15 Скачать руководство пользователя страница 16

PURELAB Prima 7/15/30

Operator Manual

ELGA

Page 12

PURELAB Prima 7/15/30 Version 01 09/08

Electrical

The units can be connected universally to any electrical supply
in the range of

100 - 240V and 50 - 60Hz.

The mains lead is

supplied with a molded plug on one end and a molded
connector to the unit on the other. The unit should be
connected to an earth.

Drain

A semi rigid flexible connection to a sink or suitable drain
capable of handling at least 1.5 l/min is required. The drain
point should have a gravity fall below the level of the unit and
any connections direct to drain should have an air-break device
fitted.

Feed Water

The feed water should be of good quality and comply with
specifications provided.

This should enter the unit via an

8mm

(5/16") OD

semi rigid tube, and should be in the temperature

range 1 to 35°C.

CAUTION!

Operating with feed water temperatures
outside the range from 1 to 35°C will cause
damage to the

PURELAB Prima

unit.

For pressurized feeds, the minimum direct inlet pressure is
4 bar (60 psi) (6 bar (90 psi) for

PURELAB Prima 30)

and

maximum inlet pressure is 6 bar (90 psi). Higher feedwater
pressures must be reduced using a pressure regulator valve
(Part No. LA 512).

Reservoir feeds to the

PURELAB Prima

unit should be

positioned at the same height, or above the unit, to provide a
positive flooded inlet pressure.

PURELAB Prima

Level control cable

RESERVOIR

Outlet

Inlet

Drain

All tube connections 8mm (5/16")

PURELAB Prima

Unit Installed with Storage Reservoir

Direction of

water flow

Collar

Collar

Mesh filter

Strainer

Feed Water Strainer

Mains power socket

Mains power lead

Fuse

ON/OFF

switch

Electrical Connections

«
...
14
15
16
17
18
...
»

Содержание PURELAB Prima 15



































Отзывы:

Нет отзывов