elero SunTop M, Инструкции по эксплуатации и монтажу

Страница: 8 / 10

5.6.10 Option D:
Upper end position freely con fi gurable,
fi xed lower end position
Option D: Upper end position freely con fi gurable,
fi xed lower end position
①
In a medium fabric position, using the installation
cable or a programmed transmitter, press the
UP
button ▲ until the fabric has reached the desired
upper end position.
The drive system starts, stops brie
fl y and starts
again (as long as the button is pressed).
Corrections can be made with the buttons
▲ and
▼ .
②
Keep the DOWN button ▼ pressed until the drive
system stops automatically.
The upper end position is set.
③
Press the DOWN button ▼ again, until the fabric
has reached the lower end position (to bottom limit
stop).
The drive system starts, stops brie
fl y and starts
again (as long as the DOWN button ▼ is pressed).
The drive system automatically stops when reaching
the lower limit stop.
④
Keep the UP button ▲ pressed until the drive sys-
tem stops automatically.
The lower end position is set.
Optional: Activation of the relief function for the
lower limit stop: refer to section 5.6.3.
End position setting of option D is completed.
Fig. 12 End position setting option D:
5.7 Transmitter programming
Important
Requirement: The drive system must be in wireless opera-
tion.
► If the end positions are not programmed, the fabric is
loosened from the winding shaft.
Programming the ( fi rst) transmitter
Instruction Result
1 Disconnecting and recon-
necting the power supply For approx. 5 minutes,
the drive system is in
programming mode.
2 On the transmitter to be
programmed, press the
programming button
P for
approx. 1 second.
The status indicator
fl ashes. Now (for
approx. 2 minutes),
the drive system is in
programming mode
(up and down move-
ment).
3 Immediately (max. 1 se-
cond) after start of the up
movement, press the
UP
button ▲ .
The status indicator
fl ashes brie fl y. The
fabric stops brie fl y,
moves on, stops and
moves downwards.
4 Immediately (max. 1 se-
cond) after start of the
down movement, press the
DOWN button ▼ .
The status indicator
fl ashes brie fl y. The
drive system stops.
The ( fi rst) transmitter is programmed.
8 | US+CA © elero GmbH
End position settings | Transmitter programming
5.6.8 Option B: Fixed upper end position,
lower end position freely con fi gurable
Option B: Fixed upper end position,
lower end position freely con fi gurable
①
In a medium fabric position, using the installation
cable or a programmed transmitter, press the
UP
button ▲ until the fabric has reached the desired
upper end position (to upper limit stop).
The drive system starts, stops brie
fl y and starts
again (as long as the UP button ▲ is pressed).
The drive system automatically stops when reaching
the upper limit stop.
②
Keep the DOWN button ▼ pressed until the drive
system stops automatically.
The upper end position is set.
Optional: Activation of the relief function for the
upper limit stop: refer to section 5.6.2.
③
Press the DOWN button ▼ again, until the fabric
has reached the desired lower end position.
The drive system starts, stops brie
fl y and starts
again (as long as the button is pressed).
Corrections can be made with the buttons
▲ and
▼ .
④ Keep the UP button ▲ pressed until the drive sys-
tem stops automatically.
End position setting of option B is completed.
Fig. 10 End position setting option B:
5.6.9 Option C:
Fixed upper and lower end position
Option C: Fixed upper and lower end position
①
In a medium fabric position, using the installation
cable or a programmed transmitter, press the
UP
button ▲ until the fabric has reached the desired
upper end position (to upper limit stop).
The drive system starts, stops brie
fl y and starts
again (as long as the UP button ▲ is pressed).
The drive system automatically stops when reaching
the upper limit stop.
②
Keep the DOWN button ▼ pressed until the drive
system stops automatically.
The upper end position is set.
Optional: Activation of the relief function for the
upper limit stop: refer to section 5.6.2.
③
Press the DOWN button ▼ again, until the fabric
has reached the lower end position (to bottom limit
stop).
The drive system starts, stops brie
fl y and starts
again (as long as the DOWN button ▼ is pressed).
The drive system automatically stops when reaching
the lower limit stop.
④
Keep the
UP button ▲ pressed until the drive sys-
tem stops automatically.
The lower end position is set.
Optional: Activation of the relief function for the
lower limit stop: refer to section 5.6.3.
End position setting of option C is completed.
Fig. 11 End position setting option C: