9 Manufacturer's
address
elero
GmbH
Antriebstechnik
Linsenhofer Str. 65
72660 Beuren
Deutschland / Germany
Phone: +49 7025 13-01
Fax:
+49 7025 13-212
[email protected]
www.elero.com
Please visit our website if you require a contact outside
Germany.
10
Disassembly and disposal
Dispose of the packaging according to current regulations.
Dispose the product after previous use in accordance with
applicable regulations. Disposal is partially subject to stat-
utory provisions. The goods to be disposed of must only be
delivered to authorised acceptance points.
Environmental information
No unnecessary packaging was used. The packaging can
be easily divided into three material types: Cardboard (box),
Styrofoam (padding) and polyethylene (bag, foam material
protective foil).
The device is made up of materials that can be reused if it
is disassembled by a specialist operation. Please observe
the local provisions on disposal of packaging material and
old devices.
Always expect additional danger that does not occur in
operation during disassembly.
WARNING
Danger of injury due to electric current.
Electric shock possible.
►
Physically disconnect power supply lines and discharge
charged energy storage. Wait for at least 5 minutes after
deactivation for the motor to cool down and the capaci-
tors to lose their voltage.
►
Use suitable, tested and stable climbing aids when per-
forming disassembly work above body height.
►
All work at the electrical system must only be performed
by the staff described in the chapter "Safety instructions
for electrical installation".
Scrapping
During the scrapping of the product, the international,
national and regional-speci
fi
c laws and regulations are to be
complied with.
Please make sure to consider material recyclability, ease of
dismantling, and separability of materials and components
as well as environmental and health hazards during recy-
cling and disposal.
CAUTION
Environmental damage at incorrect disposal
►
Electronic scrap and electronic components are subject
to the hazardous waste rules and must only be disposed
of by approved specialist operation.
►
Groups of materials such as plastics and metals of vari-
ous kinds are sorted for recycling and disposal process.
Dispose electrical and electronic components
Disposal and recycling of electric and electronic compo-
nents must comply with the applicable national laws and
regulations.
6 | EN
©
elero
GmbH
Teach in transmitter | Troubleshooting
Programming (additional) transmitter
Instructions for action
Result
4
Press the
UP
button
▲
on
the transmitter to be taught
in (additionally)
as soon as
the blind starts moving in
upwards direction (within 1
second at the most).
The status indicator
is lit brie
fl
y. The blind
stops brie
fl
y, starts
moving again and then
moves downwards.
5
Press the
DOWN
button
▼
on
the transmitter to be
taught in (additionally)
as
soon as the blind starts
moving in downwards
direction (within 1 second at
the most).
The status indicator is
lit brie
fl
y. The drive will
stop.
The additional transmitter has been through the teach-in
procedure.
Stop bidirectional radio teaching mode:
Keep the
STOP
button pushed for at least 6 seconds until
the status display lights up (depending on transmitter).
6 Troubleshooting
Problem /
Error
Possible
cause
Cure
Remedy
• Drive stops
after a short
time
• Sluggish
shutter
• Check smooth
running of the
Venetian blind
• Drive runs only
in one direction
• Connection
error
• Check connec-
tion
• Drive not
responding
• No mains
voltage
• Temperature
limiter has
tripped
• Check mains
voltage
• Allow drive to
cool
• Drive does not
learn any end
positions
• Stop missing
or no me-
chanical limit
present
• Delete end
positions
• Install mechan-
ical stops
Fig. 8 Troubleshooting for the RolTop /D+ 868
7 Maintenance
The RolTop /D + 868 is maintenance-free.
8 Repair
Please contact your dealer if you have any questions.
Please always provide the following information:
• Item number and name on the type plate
• Type of fault
• Previous and unusual events
• Surrounding circumstances
• Own assumption
