background image

V. 07-21

www.plycem.com

V. 10-21

www.plycem.com

5

INSTALLATION GUIDE FOR EUREKA CISTERN TANK

Multi connector installation.

Your  Cistern  (1)  has  a  threaded  fl ange  (2).  Screw  on  the  multi-
connector  (3)  with  a  1/2”  or  3/4”  outlet.  Use  the  one  that 

corresponds to the diameter of your distribution pipe (5). To tighten 

use  only  your  hands.  Turn  until  the  threaded  plug  of  the  air  jug 

(4) is facing upwards and the cleaning plug (6) is on one side as 

shown in the fi gure. Remove the plug and insert the air jug tube (4).

Connect the Multiconnector (3) to the distribution pipe (5).

Step 3

1

2

3

4

5

6

2. With electronivel (electrode not included). Your new Cistern has 

a  special  base  that  allows  the  placement  of  an  electric  fl oat  or 

electronivel.

Place Tefl on tape (not included) on all pipe threads and fi ttings to 

be installed. 

For the correct installation of the Cistern at fl oor level, the following 

diagram should be considered. 

1. Control alternatives (1 and 2) valve and fl oat.
To install the valve and fl oat your Cistern has a hole (3) in the upper 

neck to insert the water supply pipe (5), at the end of the pipe, using a 

union (4) (not included). Install the valve and fl oat (1 and 2) as shown.

Step 2

2

3

4 5

1

Build a fl at level base to place your cistern.

To obtain adequate pressure in the distribution line, verify that from 
the base of your cistern to the highest expected height (faucet or 
shower), there is a minimum height of 2 meters as shown.

Step 1

2 m

Male adapters

 

 

1/2”

Float

Filter

Multi connector

Tee PVC 1/2”

Valve

 Check

PVC elbolw 1/2”

Shut-off

valve

Water inlet and

outlet

Outlet pipe

support

PVC elbow1/2”

Connecting

flange

Air jug

Shut-off valve 

Electric

 panel

Power supply 

to the building

Foat

Filter

Multi connector

Outlet pipe

 support

Connecting 

flange

Air jug

Level flat base

Filling level

Water inlet 

Outlet pipe

Check valve

Pump

Tank 

Hydropneumatic

Pressure 

switch 

Note: This condition is handled upon request. The accessories of 
the overhead tank condition will be included: multi-connector, 

fl oat valve and air jug. Other accessories and the pumping system 

indicated in the diagram are not included.

Installation instructions 

INSTALLATION OF CISTERN AT GROUND LEVEL

Содержание Plycem Eureka Cistern Tank









Отзывы: