Electromotive XDI200 Скачать руководство пользователя страница 98

Страница: 98 / 99

________________________________________________________________________
XDI200 Manual Version 0.1

- Page 98 -

General Purpose Inputs (GPI):

Input channels that the

XDI200

can use to process data from

sensors that are not related to the core engine management sensors.  Switches and vehicle speed
sensors can be run to the GPIs.

General Purpose Outputs (GPO):

Output channels from the

XDI200

that can be used to trigger

external devices such as thermo fans, torque converters, etc.

Horsepower (HP):

A measurement of the rate at which an engine can perform work. One HP = 550

lb-ft per second.

Idle Air Control (IAC) Motor:

A device that is used to meter air into an engine at idle. Air from the

outside of the intake manifold is regulated into the intake plenum by the IAC motor.

Ignition Timing:

The amount of degrees before Top Dead Center that a spark plug fires.

Knock Sensor:

A device used to measure detonation.

Knocking:

see ‘Detonation’

Load:

The amount of work that an engine must provide at a given instant. Load is measured by

using the MAP sensor to estimate the cylinder pressure on

XDI200

systems. Higher loads result in

higher MAP readings.

Manifold Air Pressure (MAP) Sensor:

A device that measures the absolute pressure of the intake

charge for an engine.

Manifold Air Temperature Enrichment:

An inlet air temperature-based enrichment that is used to

add fuel when the incoming air is cold, and therefore denser than usual.

Manifold Air Temperature (MAT) Sensor:

A device that measures the temperature of the incoming

air charge for an engine.

Millisecond (ms):

A length of time equal to one one-thousandth of a second.

1 millisecond = 0.001 second

Pinging:

See ‘Detonation’.

Retard:

As applied to ignition timing, retarding the timing refers to firing the spark plug comparatively

later.

Rich Mixture:

An air-fuel mixture that carries more fuel than the stoichiometric air-fuel ratio.

Spark Knock:

See ‘Detonation’

TDC (Top Dead Center):

On piston engines, when a piston is at its highest point (closest to the

cylinder head), and the combustion chamber is at its smallest volume, it is at TDC. TDC#1 refers to
the case when the #1 cylinder is on TDC. On rotary engines, TDC occurs when the combustion
chamber volume is smallest.

Содержание XDI200




































































































Результаты поиска

Содержание XDI200

Отзывы:

Похожие инструкции для XDI200

Бренды по названию

Популярные бренды

Electromotive XDI200, Руководство по установке и инструкция пользователя

Результаты поиска

Содержание XDI200

Отзывы:

Похожие инструкции для XDI200

Бренды по названию

Популярные бренды