Electromotive XDI200 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 99

background image

________________________________________________________________________
XDI200 Manual Version 0.1

- Page 67 -

©2017 Electromotive, Inc.

7 Communications Ports on the XDI200

The XDI200 has 3 serial communications ports built into it. You must connect to one of

them to program the XDI200.

7.1.1 PC communications, USB port

The built in USB port allows you to directly connect the XDI200 to your laptop computer

without an adapter. Use the connector built into the wire harness to plug directly into your laptop.
Wh

en plugging the USB jack into your computer, you should hear the “beep-beep” that tells you

that Windows has found the USB equipped XDI200 and that the driver is loading automatically
from Windows. You may have to have your computer connected to the internet to complete this
task. Use Electromotive’s Wintecc4 to begin the calibration process. When opening Wintec4,
make sure that Wintec4 discovers your USB connection and its on the correct port number.

Note on finding the USB port:

If Wintec4 cannot find the USB port it is because the PC has assigned the new USB connection
to a number higher than 12.  To correct this, go to your computer control panel and select
hardware device manager. Then look at Ports, If the USB port number shows a number higher
than 12, select that port and then select advanced.  Change the port number to one that is less
than 12.  Close that and go to Wintec4 control options and change the communications to that
new port number.

7.1.2 PC communications, RS232 Serial port

The XDI200 also has the old style RS232 serial port that some PC computers still have.

The XDI200 functions will work identically for either USB or RS232. Do not use both ports at the
same time. Make sure the Wintec4 software finds the right port number, usually 1 or 2.

7.1.3 CAN bus serial port

XDI200 has a built in CAN bus port to transmit engine data to other computers on your car.

Your supplier of the other computers should have already contacted Electromotive on the details
of the data stream. Remember to turn the CAN bus data on in the calibration set up if you need
it.

Serial
Port

Pin Color

Function

RS 232

30 Brown in 7 conductor
cable

Ground

RS 232

31 Orange in 7 conductor
cable

RXD

RS 232

32 Blue in 7 conductor cable

TXD

USB

35 Black & Shield in 7 cond.
cable

USB Gnd

USB

36 Red in 7 conductor cable

USB PC 5V

USB

37 White in 7 conductor

USB D-

USB

38 Green in 7 conductor

USB D+

CAN

51 Yellow/Pink

CAN High

CAN

52 Green/Pink

CAN Low

Table. Summary of Serial Communications Ports

«
...
65
66
67
68
69
...
»

Содержание XDI200




































































































Отзывы:

Нет отзывов

Похожие инструкции для XDI200

Бренд: NEC Страницы: 144

Бренд: Panasonic Страницы: 289

Бренд: Datalogic Страницы: 248

Multi Function Professional Puncher-A1

Бренд: Canon Страницы: 44

Бренд: JANE Страницы: 21

Бренд: Imax Страницы: 3

Бренд: Larson Electronics Страницы: 2

Бренд: Axxess Страницы: 4

Бренд: Vintage Air Страницы: 14

Бренд: AMP Research Страницы: 12

Half Size Trunk Box Organizer C-TBO-CV

Бренд: Havis-Shields Страницы: 1

Бренд: Volvo Страницы: 8

Бренд: MAXWORKS Страницы: 7

Бренд: Veko Страницы: 2

Бренд: N-Com Страницы: 6

Pro Swing OA-Edge T

Бренд: Optex Страницы: 2

Бренд: Toyota Страницы: 52

Бренд: Anslut Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды