manualshive.com logo in svg

Electrolux W5105N, Руководство по установке

Поделиться
Скачать
Electrolux W5105N Скачать руководство пользователя страница 16

16

Setup

3.3.2 Chemical bolts

An alternative to breaking up the existing floor or foundation is to use chemical bolts M16.

1. Mark and drill four holes (

⌀

18 mm) 125 mm deep for the chemical bolts.

Check the previous table for the correct position of the holes.

2. Clean the drilled holes.

3. Put down the chemical ampule in the hole.

4. Rotate the bolt into the hole, so that the glass ampule is broken and its contents mixed.

5. Rotate the bolt to correct depth.

Note!

Do not rotate the bolt against the concrete bottom. Check that the chemicals have filled
the hole completely.

6. Remove the drilling machine with the mounting tool. Hold the bolt with one hand. Let the bolt

harden before the machine is mounted.

⑦

1

2

3

4

5

6

fig.5917A

Time for hardening, due to different concrete temperatures:
– 10°C: 6 hours
– 5°C: 2.5 hours
± 0°C: 1 hour
5°C: 30 minutes
10°C: 20 minutes
15°C: 15 minutes
20°C: 10 minutes

Содержание W5105N

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды