Electrolux W4300H страница 127 Скачать руководство пользователя | Manualshive

Страница: 127 / 140

background image

127

Troubleshooting

Error code 33, NO INTERLOCK

This error code is generated by the motor control. The motor control must

be powered with 230V/50 or 60 Hz on the interlock input in order to drive

the motor. This signal is a confirmation that the door is closed and locked.
Motor control receives its commands to rotate the drum from the timer via
a serial communication link between the motor control and timer. Since the
timer also has access to the interlock signal, the timer must never send a
run command to the motor control if the interlock signal is missing. If this
does happen, the ”No interlock” error code will be activated.
The cause of this error code being activated can be e.g. a break in the ca-
ble leading the interlock signal to the motor control. There may also be an

error in the connector in the door lock, which connects 230V/50Hz to the

interlock signal. An error in the interlock circuits of the motor control can
also set this error code.
Actions:

• Use a measuring instrument to check that the interlock signal comes on

X302:1-2 when the door lock is activated. Read also bit 1 in the second
byte under ”Motor Status” in the service program (the bits are numbe-
red from 0 to 7 where bit 0 is on the far right). If bit 1 in the second byte
is 1 then the lock is open, while a 0 indicates that the lock is closed.

• Replace the defective part when it has been located.

«
...
125
126
127
128
129
...
»

Содержание W4300H













































































































































Отзывы:

Нет отзывов

Похожие инструкции для W4300H

Бренд: Canmac Страницы: 17

Бренд: Paula Deen Страницы: 72

Бренд: Adler Europe Страницы: 60

Бренд: Smeg Страницы: 32

MANROSE FAN5653

Бренд: SImx Страницы: 2

Бренд: GGMgastro Страницы: 9

Бренд: Dolphin Dispensers Страницы: 3

Бренд: Sunbeam Страницы: 9

Бренд: Morphy Richards Страницы: 6

Бренд: Asko Страницы: 24

Бренд: Magnani Страницы: 40

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 3

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 14

Бренд: Frigidaire Страницы: 8

Бренд: Frigidaire Страницы: 14

gallery FDG747GES0

Бренд: Frigidaire Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды