Electrolux W4300H Скачать руководство пользователя

Страница: 99 / 140

K21

K22

Y51

6665 A

6666

Function (machines built for mop washing)

Electric heating without fusible cut-out on

element

The three heating elements in the machine are
connected to separate phases and switched on

and off using two serial heating contactors. Hea

ting contactor K21 is controlled by programme
unit A1, output (x36:7). Heating contactor K22 is

regulated by a standalone mechanical level con-

trol. In order for both contactors to be activated,

the level in the machine must have been appro-
ved by both the level control in programme unit

A1 and the mechanical level control.
The water level in the machine must be 90 scale
units or more in order for the mechanical level

control to be activated.

The programme unit receives information on the

water temperature in the machine through an

analogue signal from the temperature sensor

situated in the outer drum. The programme unit
controls the heating contactors to achieve the

set water temperature for the current washing

programme.
The mechanical level control prevents the ele-

ment from activating if the programme unit or

ders heat despite the fact that there is no water

in the drum.

Steam heating

The steam valve is controlled by the programme

unit A1, output (X3 36:7).

Heating

  1.  Heating elements
2a.  Programme unit A1
2b.  Interlock signal
  3.  Supply voltage
  4.  Temperature sensor
  5.  I/O Board
  6.  Level control

  1.  Steam valve
  2.  Programme unit A1
  3.  Rear control unit
  4.  Temperature sensor

5. I/O-card

Содержание W4300H













































































































































Результаты поиска

Содержание W4300H

Отзывы:

Похожие инструкции для W4300H

Бренды по названию

Популярные бренды

Electrolux W4300H, Руководство по обслуживанию

Результаты поиска

Содержание W4300H

Отзывы:

Похожие инструкции для W4300H

Бренды по названию

Популярные бренды