background image

Malfunction

Possible cause and solution

The programme does not start

• The dishwasher door has not been properly

closed.
Close the door.

• The main plug is not plugged in.

Insert the main plug

• The fuse has blown out in the household fuse

box.
Replace the fuse.

• Delay start has been set.

If dishes are to be washed immediately, cancel
the delay start.

Once these checks have been carried out
switch on the appliance.
The programme will continue from the point
at which it was interrupted.
If the malfunction or fault code reappears
contact your local Service Force Centre.
For other fault codes not described in the
above chart, please contact your local Serv-
ice Force Centre.
Contact your local Service Force Centre,
quoting the model (Mod.), product number
(PNC) and serial number (S.N.).

This information can be found on the rating
plate located on the side of the dishwasher
door.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The wash results are not satisfactory

The dishes are not
clean

• The wrong programme has been selected.
• The dishes are arranged in such a way as to stop water reaching all parts

of a surface. The baskets must not be overloaded.

• The spray arms do not rotate freely due to incorrect arrangement of the

load.

• The filters in the base of the washing compartment are dirty or incorrectly

positioned.

• Too little or no detergent has been used.
• Where there are limescales deposits on the dishes; the salt container is

empty or incorrect level of the water softener has been set.

• The drain hose connection is not correct.
• The salt container cap is not properly closed.

The dishes are wet
and dull

• Rinse aid was not used.
• The rinse aid dispenser is empty.

There are streaks,
milky spots or a blu-
ish coating on
glasses and dishes

• Decrease rinse aid dosage.

Water drops have
dried onto glasses
and dishes

• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent manufacturer con-

sumer care line.

If after all these checks, the problem persists,
contact your local Service Force Centre.

Technical data

Dimensions

Width cm

59,6

 

Height cm

85

electrolux 

 19

Содержание ESF66830





























Отзывы: