background image

External cleaning

Clean the external surfaces of the machine
and control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or sol-
vent (acetone, trichloroethylene etc...).

Internal cleaning

Ensure that the seals around the door, the
detergent and rinse aid dispensers are
cleaned regularly with a damp cloth.
We recommend every 3 months you run the
wash programme for heavy soiled dishes us-
ing detergent but without dishes.

Prolonged periods of non-operation

If you are not using the machine for a pro-
longed period of time you are advised to:
1. Unplug the appliance and then turn off

the water.

2. Leave the door ajar to prevent the forma-

tion of any unpleasant smells.

3. Leave the inside of the machine clean.

Frost precautions

Avoid placing the machine in a location
where the temperature is below 0°C. If this is
unavoidable, empty the machine, close the
appliance door, disconnect the water inlet
pipe and empty it.

Moving the machine

If you have to move the machine (moving
house etc...):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge

hoses.

4. Pull the machine out together with the

hoses.

Avoid over tilting the machine during trans-
portation.

What to do if…

The appliance will not start or stops during
operation.
Certain problems can be due to the lack of
simple maintenance or oversights, which can

be solved with the help of the hints described
in the chart, without calling out an engineer.
Switch off the appliance and carry out the
following suggested corrective actions.

Fault codes and malfunction

Possible cause and solution

• digital display shows 

The appliance does not fill with water

• The water tap is blocked or furred with lime-

scale.
Clean the water tap.

• The water tap is turned off.

Turn the water tap on.

• The filter (where present) in the water inlet hose

is blocked.
Clean the filter in the water inlet hose.

• The water inlet hose has not been correctly laid

or it is kinked or squashed.
Check the water inlet hose connection.

• digital display shows 

The appliance does not drain

• The sink spigot is blocked.

Clean out the sink spigot.

• The water drain hose has not been correctly laid

or it is kinked or squashed.
Check the water drain hose connection.

• digital display shows 

Anti-flood device is activated

• Close the water tap and contact your local

Service Force Centre.

18 

 electrolux

Содержание ESF66830





























Отзывы: