Electrolux ei28bs55is1 Скачать руководство пользователя

Страница: 14 / 49

Connecting the Water Supply

Before installing the water supply line, you

will need:

1. Basic Tools: adjustable wrench, flat-blade

screwdriver, and Phillips

screwdriver

2. Access to a household cold water line with

water pressure between 30 and 100 psi.

3. A water supply line made of ¼ inch

(6 mm) OD, copper or stainless steel

tubing. To determine the length of tubing

needed, measure the distance from the

ice maker inlet valve at the back of the

refrigerator to your cold water pipe. Then

add approximately 7 feet (2.1 meters),

so the refrigerator can be moved out for

cleaning (as shown).

To connect water supply line to ice maker

inlet valve:

1. Disconnect refrigerator from electric

power source.

2. Place end of water supply line into sink

or bucket. Turn ON water supply and

flush supply line until water is clear. Turn

OFF water supply at shutoff valve.

3. Remove plastic cap from water valve

inlet and discard cap.

4. If you use copper tubing - Slide brass

compression nut, then ferrule (sleeve)

onto water supply line. Push water

supply line into water valve inlet as far

as it will go (¼ inch / 6 mm). Slide ferrule

(sleeve) into valve inlet and finger tighten

compression nut onto valve. Tighten

another half turn with a wrench; DO NOT

over- tighten. See Figure 1.

If you use stainless steel tubing - The nut

and ferrule are already assembled on the

tubing. Slide compression nut onto valve

inlet and finger tighten compression nut

onto valve. Tighten another half turn with

a wrench; DO NOT over- tighten. See

Figure 2.

5. With steel clamp and screw, secure

water supply line (copper tubing only) to

rear panel of refrigerator as shown.

6. Coil excess water supply line (copper

tubing only), about 2½ turns, behind

refrigerator as shown and arrange coils

so they do not vibrate or wear against

any other surface.

7. Turn ON water supply at shutoff valve

and tighten any connections that leak.

8. Reconnect refrigerator to electrical

power source.

9. To turn ice maker on, lower wire signal

arm (freezer ice maker) or set the ice

maker’s On/Off power switch to the “On”

position (fresh food ice maker).

WARNING

To avoid electric shock, which can

cause death or severe personal injury,

disconnect the refrigerator from

electrical power before connecting a

water supply line to the refrigerator.

CAUTION

To Avoid Property Damage:

• Copper or Stainless Steel braided

tubing is recommended for the

water supply line. Water supply

tubing made of ¼ inch plastic is

not recommended to be used.

Plastic tubing greatly increases the

potential for water leaks, and the

manufacturer will not be responsible

for any damage if plastic tubing is

used for the supply line.

• DO NOT install water supply tubing

in areas where temperatures fall

below freezing.

• Chemicals from a malfunctioning

softener can damage the ice maker.

If the ice maker is connected to soft

water, ensure that the softener is

maintained and working properly.

IMPORTANT

Ensure that your water supply line

connections comply with all local plumbing

codes.

4. A shutoff valve to connect the water

supply line to your household water

system. DO NOT use a self-piercing type

shutoff valve.

5. Do NOT reuse compression fitting or use

thread seal tape.

6. A compression nut and ferrule (sleeve)

for connecting a copper water supply

line to the ice maker inlet valve.

Содержание ei28bs55is1


















































Результаты поиска

Содержание ei28bs55is1

Отзывы:

Похожие инструкции для ei28bs55is1

Бренды по названию

Популярные бренды

Electrolux ei28bs55is1, Инструкция по использованию и уходу

Результаты поиска

Содержание ei28bs55is1

Отзывы:

Похожие инструкции для ei28bs55is1

Бренды по названию

Популярные бренды