Electrolux ei28bs55is1 страница 7 Скачать руководство пользователя

Страница: 7 / 49

Installation

Toe Grille Must

Fit in Slot on

Anti-tip Bracket

Screw/Washer

Assembly

(3) Retaining Clips

To level the cabinet using the front rollers:

1 Slightly open freezer drawer. Lift the

toe grille and gently pull forward (see

illustration).

2 You can raise or lower each door. Use

⅜

inch socket wrench to turn the

adjustment screws (1 per side).

Leveling Freezer Drawer

(if necessary)

1 Check gasket seal around top, bottom,

and sides of freezer drawer.

2 If gasket is not sealed, open drawer and

slightly loosen four drawer screws (two

on each side) to allow drawer to rotate.

3 Close drawer and recheck the seal

on the gasket (A). Open the drawer

grabbing by the sides in the center (B).

Be careful not to rotate the drawer.

Grab

Drawer

at Center

from Both

Sides

Then

Pull

Drawer

Out

Push

Against

Freezer

Drawer

4 Tighten four drawer screws.
5 Recheck gasket seal.

Level Refrigerator & Adjust

Doors (if necessary)

Guidelines for final positioning of your

refrigerator:

•

All four corners of the cabinet must rest

firmly on the floor.

•

The sides should tilt ¼ inch (6 mm) from

front to back (to ensure that doors close

and seal properly).

•

Doors should align with each other and

be level.

Most of these conditions can be met by

raising or lowering the adjustable front rollers.

Raise

Anti-tip

Leg

Door

Lower

Door

To raise

: turn adjustment screw

clockwise.

To lower

: turn adjustment screw

counterclockwise.

3 Ensure both doors are bind-free with

their seals touching the cabinet on all

four sides and that cabinet is stable.

4 After unit is leveled, lower anti-tip leg

until it contacts the floor.

Remove

Hex

Head Drawer

Screw

Remove hex

head drawer

screw

Remove

Hex

Head Drawer

Screw

Remove hex

head drawer

screw

Do Not Remove

Other Screws

5 Install the toe grille by fitting into place.

Содержание ei28bs55is1


















































Результаты поиска

Содержание ei28bs55is1

Отзывы:

Похожие инструкции для ei28bs55is1

Бренды по названию

Популярные бренды

Electrolux ei28bs55is1, Инструкция по использованию и уходу

Результаты поиска

Содержание ei28bs55is1

Отзывы:

Похожие инструкции для ei28bs55is1

Бренды по названию

Популярные бренды