Auto operation
Ensure the unit is plugged in and power is available. The OPERATION indicator
on the display panel of the indoor unit starts flashing.
1. Press the MODE button to select Auto.
2. Press the UP/DOWN button to set the desired temperature. The temperature
can be set within a range of 17°C~ 30°C in 1°C increments.
3. Press the ON/OFFbutton to start the air conditioner.
Note:
1. In the Auto mode, the air conditioner can logically choose the mode of
Cooling, Fan, and Heating by sensing the difference between the actual
ambient room temperature and the setting temperature on the remote
controller.
2. In the Auto mode, you can not switch the fan speed. It has already been
automatically controlled.
3. If the Auto mode is not comfortable for you , the desired mode can be
selected manually.
1
How the air conditioner works
Dehumidifying operation
Ensure the unit is plugged in and power is available. The OPERATION indicator
on the display panel of the indoor unit starts flashing.
1. Press the MODE button to select DRY mode.
2. Press the UP/DOWN buttons to set the desired temperature. The
temperature can be set within a range of 17°C~ 30°C in 1°C increments.
3. Press the ON/OFF button to start the air conditioner.
In the Dehumidifying mode, you can not switch the fan speed. It has already
been automatically controlled.
Cooling /Heating/Fan operation
Ensure the unit is plugged in and power is available.
1. Press the MODE button to select COOL, HEAT(cooling & heating models
only) or FAN mode.
2. Press the UP/DOWN buttons to set the desired temperature. The
temperature can be set within a range of 17°C~ 30°C in 1°C increments.
3. Press the FAN button to select the fan speed in four steps- Auto, Low,
Med,or High.
4. Press the ON/OFF button to start the air conditioner.
In the FAN mode the setting temperature is not displayed in the remote
controller and you are not able to control the room temperature either. In this
case, only step 1, 3 and 4 may be performed.
Adjusting air flow direction
Use the SWING UP/DOWN and SWING < > buttons to adjust the desired
airflow direction.
1. When push the SWING UP/DOWN button, the horizontal louver changes 6
degree in angle for each push If pushing more than 2 seconds, the louver will
automatically swing up and down.
2. When push the SWING < > button, the vertical louver changes 6 degree in
angle for each push. If pushing more than 2 seconds, the louver will
automatically swing left and right.
When the louver swing or move to a position which would affect the
cooling or heating effect of the air conditioner, it would automatically
change the swing/moving direction.
Turbo/self clean function
Press this button less than 2nds will initiate TURBO function. And if keep
pressing this button more than 2nds,the SELF CLEAN function is initiated.
Turbo function enables the unit to reach the preset temperature in the shortest
time. When press this button on cooling mode, the unit will blow strong cooling
air with super high fan speed. When press this button on heating mode
(applicable to the unit adopts PTC only), the PTC will be energized and bring
fast heating operation.
Under SELF CLEAN mode, the air conditioner will automatically clean and dry
the Evaporator and keep it as fresh for the next operation.
LED/FOLLOW ME function
Press this button less than 2nds will initiate LED function. And if keep pressing
this button more than 2 seconds the FOLLOW ME function is initiated.
When the FOLLOW ME function is activated remote display is actual
temperature at its location.
The remote control will send this signal to the air conditioner every 3 minutes
interval until press the FOLLOW ME button again. The Follow Me function is not
available under DRY and FAN mode. Switch the operation mode or turn off the
unit will cancel the Follow Me function automatically.
39 electrolux
how the air conditioner works
how the air conditioner works
electrolux 40
