Electrolux DIVA Скачать руководство пользователя страница 12

Страница: 12 / 48

Detection of load

The quantity of dishes loaded (full or 1/2 load)

is detected during the first heating phase in the
washing cycle by measuring the speed of water
temperature increase (NTC sensor, connector H8).

Full load:

when the slope of the curve is less

than the programmed standard threshold

Half load

when the slope of the curve is

greater than the programmed standard
threshold

Phases in the automatic programme

Shown below are the variations in programme phases which are made as a function of dirt level and load.

Type

Phases in the programme

Load

Very

dirty?

Prewash

Wash

First rinse

Second rinse Hot rinse

Drying

Full Yes

68º

cold

Full No

55º

Half full

Yes

55º C

Half full

cold

50º C

cold

68º C

24 min.

4.2 Selecting a programme

1. Close the door and turn the appliance on by pressing button

The relative LED L0 lights up
The LCD display lights up with a welcome message and then flashes the last programme run (to run

this programme again, skip to point 4)

2. To choose a different programme:

a) On the free-standing model, press the button for the

desired programme

(S1-S5)

: the relative LED lights up to

confirm that the selection has been made, see fig. 2a

b) On the built-in model, press button

repeatedly until the

desired programme appears on the display; see fig. 2b

3. The following then appears on the LCD:

  The name of the programme, which flashes
  The time in minutes from the beginning to the end of the cycle
  Segments at the top of the display, in the same number as the number of washing phases in the

programme selected

The symbols that characterise the programme

fig. 2a

fig. 2b

temperature

time

threshold

1/2 load

full load

Содержание DIVA

















































Результаты поиска

Содержание DIVA

Отзывы:

Похожие инструкции для DIVA

Бренды по названию

Популярные бренды

Electrolux DIVA, Руководство по обслуживанию

Результаты поиска

Содержание DIVA

Отзывы:

Похожие инструкции для DIVA

Бренды по названию

Популярные бренды