CAUTION
Care must be taken to ensure the screws are not cross threaded when
attaching the upper flue cover.
If installed in recirculating mode, insert the optional carbon
filter (included in recirculation kit AR910RK).
To complete the rangehood installation, insert the three
filters to the underside of the hood body. Place back edge
of filter into position and push up front edge so that the
filter clips into place.
Your Westinghouse rangehood is now ready to use.
INSTALLATION
7.
Electrical connection
Check that the installation complies with the standards
of local building, gas and electrical authorities. Before
connecting to the mains supply ensure that the mains
voltage corresponds to the voltage on the rating plate
inside the rangehood.
Installation of telescopic flue covers
Separate the inner and outer flue covers, and carefully
remove the protective coating from both. Carefully
reassemble the upper and lower flue covers sections by
sliding the inner into the outer flue cover. Carefully lower
the assembled upper and lower flue covers onto the top
of the rangehood body, and insert the flue cover into the
rangehood body approximately 5mm. Fix upper flue cover
to the wall mounting bracket with screws supplied. Ensure
that the upper section is extended.
CONTROL PANEL
• Best results are obtained by using a low speed for
normal conditions and a high speed when odours are
more concentrated.
• Turn the hood on for a few minutes before you
start cooking.
• The hood should be left on for 15 minutes after cooking
or until all odours have dispersed.
• The control switches are located on the front panel of the
unit. See
Fig. 12 below.
Fig. 12
• The control panel comprises of:
–
T
: Indicator lamp
–
U
: Light button
–
V
: Off button
–
W
: 3 control switches for the motor
(speed positions 1, 2, and 3)
CONTROL PANEL
Fig. 11
User manual_CS910CS
28/11
/2012
CARE & MAINTENENCE
CAUTION
External surfaces are susceptible to scratches and abrasions, so
please follow the cleaning instructions to ensure the best possible
result is achieved without damage.
Cleaning the hood
• Clean the outside of the hood using a damp cloth and
a solution of water and mild washing up liquid. Clean
stainless steel surfaces using non-abrasive cleaning
products that are specifically for use on stainless steel.
To ensure best results also use an even pressure and
follow the grain of the stainless steel. Use of a soft cloth
reduces the risk of scratching. If the cloth is wet ensure
that a dry soft cloth is used to wipe down the surface
again reducing the risk of any surface rust appearing.
• Never use corrosive, abraisive or flammable cleaning
products or products containing bleach.
• Never insert pointed objects in the motor’s
protective grid.
• Only ever clean the switch panel and filter grill using a
damp cloth and mild washing up liquid.
• It is extremely important to clean the unit and change the
filters at the recommended intervals. Failure to do so will
cause grease deposits that could cause a fire.
Removing the metal grease filters
• Push the grease filter towards the back of the unit and
then pull it down and out.
Hand washing
Soak grease filters for about one hour in hot water with a
grease-loosening cleaner, then rinse off thoroughly with hot
water. Repeat the process if necessary. Refit the grease filters
when they are dry.
Dishwasher
Place grease filters in the dishwasher. Select the most
powerful washing program and highest temperature, at
least 65°C. Repeat the process. Refit the grease filters when
they are dry. When washing the metal grease filter in the
dishwasher a slight discolouration of the filter can occur, this
does not have any impact on it’s performance.
NOTE: The metal grease filters must be removed and washed,
either by hand or in the dishwasher, every four weeks.
• Clean the inner housing using a hand hot solution only
(never use caustic detergents, abrasive powders or brushes).
Charcoal filter
• The charcoal filter should only be used if you want to use
the hood in the recirculation function.
• This filter cannot be cleaned or re-used and as a general
rule, the activated charcoal filter should be changed once
every four months.
Fitting the charcoal filter
Fit one charcoal filter on the left and one on the right so as
to cover the plastic grids that protect the fan wheel.
• Always specify the hood model code number and
serial number when ordering replacement filters. This
information is shown on the registration plate located on
the inside of this unit.
• Replacement charcoal filters can be ordered from your
local Service Centre.
