background image

Page 40

P/N 316439221

ES 340 CONTROL

ES 340 Control Features:

• Automatic oven (Delay, Cook, and Off)
• Full slew up / down control 
• Digital Time and Temperature Display 
• Electronic Clock and Countdown Timer (12 Hour) 
• Dual Radiant™ Baking (electric models) 
• Variable broil (2 positions) 
• 2 Pre - programmed clean cycles
  (2 hour 

Speed clean

 - 3 hour 

Clean

 ) 

• 12 hour energy saving shut-off with override for 
   continuous operation 
• Selectable Fº or Cº temperature readout 
• Control Lockout (disables oven and locks door) 
• Oven Light Switch on control. 
• User Adjustable Oven Temperature Offset

ES 510 CONTROL

ES 510 Control Features:

• Convection Bake and Convection Roast settings
• Automatic Convection Conversion feature
• Sabbath Mode (Star-K Certified)
• Keep Warm Feature - Maintains 170

°

F oven 

  temperature for up to 3 hours. 
• Favorite Setting - User can program and store up 
  to 3 different bake or timed bake cycles 
• Automatic oven (Delay, Cook, and Off)
• Numeric Keypad Temperature Selection 
• Digital Time and Temperature Display 
• Electronic Clock and Countdown Timer (12 Hour) 
• Dual Radiant™ Baking (electric models) 
• Variable broil - Temperature adjustable between    
  400

°

F & 550

°

F

• 3 Pre - programmed clean cycles
  (2 hour 

Speed clean 

- 3 hour 

Clean

 - 4 hour  

   

Maxx clean

• 12 hour energy saving shut-off with override for 
   continuous operation 
• Selectable Fº or Cº temperature readout 
• Control Lockout (disables oven and locks door) 
• Oven Light Switch on control. 
• User Adjustable Oven Temperature Offset

Sales Demo Mode

A sales demo (SD) mode is available in the ES510 control that allows the control panel functions to 
be demonstrated without turning on any burners or elements. To enter or exit the SD mode disconnect 
power to the range. Reconnect the power and within 45 seconds touch the         keypad on the EOC 
and hold until “

sd

” appears in the EOC display (approximately 6 seconds). The ESEC display windows 

will also display “sd” momentarily and then go blank. The time of day display will blink until the clock is 
set. In the Sales Demo mode all control panel and display functions can be demonstrated but the ele-
ments will not heat. 

To exit the Sales Demo mode 

you 

must

 repeat the procedure used to enter the Sales Demo mode. 

Disconnect the power to the range; reconnect the power and within 45 seconds touch and hold the   
        pad until the “sd” display disappears. You can not exit the Sales Demo mode by pressing the 
Stop/Clear keypad or by resetting the power to the range. 

Bake 

time

Bake 

time

Содержание 30" GAS FREESTANDING RANGES












































Отзывы: