Electrolab RediLevel 2100 DLS Скачать руководство пользователя страница 28

Страница: 28 / 29

RediLevel 2100 DLS

page 24

EL 29306

Part Numbering System

The sample below is the part number for a 12-foot sensor with ¼ inch resolution, one temperature

sensor, and a single float going into a tank with a 2-inch port and being wired up as two-wire RS485.

Figure 4. RediLevel 2100 DLS Part Numbering System

In addition to the information provided within the part number, other information is necessary when

ordering:

Total Tube Length:

Default is Measurement Length plus 18 inches.

Note: If installing in a dome-top tank, like a fiberglass tank, you will need to order a

sensor that is 1’ longer than the tank height to accommodate the extra height the dome

adds.

Baud Rate and Parity desired:

Default is 9600, N, 8, 1. If other baud rate and parity are

required, please specify.

Unit Numbers Required:

If ordering more than one sensor for a location, then you may

have the level sensors pre-addressed with the required unit numbers prior to shipment

for the tanks on that location. Example: If there are 3 tanks on one location, then specify

that the level sensors be addressed U01, UO2, and U03. Alternate numbering sequences

may be chosen. If no unit numbers are specified, then default will be Unit 01.

TFX12S25T1F2-RL

Resolution of

Measurement

25 = ¼”

# of Floats

1 = Single Float

2 = Dual Float

Height of Tank

In Feet

2 to 12 ft.

S = Stainless Steel

# of Temperature

Measurements

1 is standard

Up to 8 available

RediLevel

Содержание RediLevel 2100 DLS


























Результаты поиска

Содержание RediLevel 2100 DLS

Отзывы:

Бренды по названию

Популярные бренды

Electrolab RediLevel 2100 DLS, Руководство пользователя

Результаты поиска

Содержание RediLevel 2100 DLS

Отзывы:

Бренды по названию

Популярные бренды