background image

Operating mode :
-DMX control 17  channels/Stand-alone  with built-in microphone/ Stand-alone  with  automatic mode/
Master/Slave mode.

3.Moving head starting up :

3.1. Access to main functions

Control panel:

”MENU“ 

“▼ ”

 “▲”

 ”ENTER”

Press the “

MENU

” button to access functions then « ▼ » or « ▲ » to browse through sub-menus,

«

 ENTER 

» to confirm.“

MENU

” to go back.

3 operating modes are available :  DMX control , Stand-alone/sound mode and Manual mode

Set

RunMode

DMX
Stand-alone mode : Auto 1 /Auto 2 / random
Sound mode

DMX Address

DMX address selection from 001 to 512

Channel mode

Mode selection 17 DMX channels

Inverse Pan

ON/OFF    pan inversion

Inverse Tilt

ON/OFF    tilt inversion

Pan-Tilt Swap

ON/OFF    pan and tilt inversion

Pan-Tilt encoder

ON/OFF   position sensor

No DMX Signal

Moving head behavior in case of DMX signa loss
Keep = keep last received DMX values
Clear = DMX values reset

Linear change of color

ON/OFF color wheel linear rotation

Load default

Back to factory configuration

Manu

Pan, Tilt, Dimmer,..

Moving head manual setting

Sys

Ver

Firmware version /DMX channel/time since activation/nb of
total hours

Reset Cal

Setting :offset fin upon start, pan/tilt, wheels,,,,

Sensor monitor

Motor position sensors values

System errors

Indexed system errors

DMX monitor

Current received DMX values

3.2 DMX wiring 

  This device uses 3-pin XRL connectors for the  DMX512 connection:

Pin 1connected to ground, Pin 2 connected to coldspot (-), Pin 3 connected to hotspot (+).
Example : connection between different fixtures in Master/Slave mode:
All   fixtures   must   be   at   the   same   DMX   address,     1

st

  projector   in  Auto   or   Sound   mode,   following

projectors  in DMX mode on the same address of the Master projector.
NB   :   in   order   to   reduce   signal   errors,   think   of   using   a   plug   a   the   end   of   your   DMX   link.

5

Содержание M SPOT 200II










Отзывы: