background image

All three channels are setup this way.  By default, when a given channel 

is active both the SEND SWITCH and RETURN SWITCH are closed, 
allowing signal to flow through them.  When a given channel is inactive, 

both of these switches are open, blocking any signal from flowing.  
Advance options allow you to change how this works, expanding the Tri 

Parallel Mixer’s possible applications.

 

 

BOTH, SEND, & RETURN MUTING MODES 

 

There are three “Muting Modes” that each channel can be independently 

set to.  The default mode, explained above, is BOTH, where when a 

channel is inactive both the SEND and RETURN sides of the channel are 
muted.  The two other modes are: 

 

SEND MUTING 

 

In this mode, when a channel is inactive only the 

SEND SWITCH is opened.   The RETURN SWITCH is always closed.  This 
is useful if you have an effect such as a delay or reverb in an effects loop 
channel and you want the tails or decay of that effect to naturally fade 

out after switching the channel off. 
 

RETURN MUTING 

 

In this mode, when a channel is inactive only the 

RETURN SWITCH is opened.  The SEND SWITCH is always closed and 
signal will always come out of the SEND 1/2/3 jack even when a channel 

is inactive. 
 

To switch between these modes: 

1)

 

Hold any one of the three footswitches down for about a second 
until all three upper LEDs are blinking.   

2)

 

Once here, as you press and release a given channel’s 

footswitch, that LED will change blinking speeds.

 

3)

 

There are three blinking speeds, representing the three muting 
modes.  The slowest speed sets that channel to BOTH, the 
medium speed is SEND MUTING (useful for tails), and the 
fastest speed is RETURN MUTING.  

 

4)

 

Once you’ve set your channels to the desired modes, hold any 

one of the three footswitches for about a second until the LEDs 
stop blinking.

 

 

AND / XOR MODES 
 

By default, clicking the footswitch of a given channel turns that channel 
on or off without affecting any other channels.  This is called AND Mode.  
You can also set the Tri Parallel Mixer to XOR (exclusive or) Mode.  In 
this mode, only one of the three channels can be active at a time.  

Содержание TRI PARALLEL MIXER













Отзывы: