background image

- FCC COMPLIANCE - 

 

This device complies with part 15 of the FCC Rules. Operation is subject 

to the following two conditions:  (1) This device may not cause harmful 

interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation. If the device 

is not installed and used in accordance with the instructions, it may 

cause harmful interference to radio communications and void the user's 

authority to guarantee the equipment.

 

 

Note: 

This equipment has been tested and found to comply with the 

limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment 

generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If 

this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and 

on, the user is encouraged to try to correct the interference by one or 

more of the following measures:  

 

 

Reorient or relocate the receiving antenna.  

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.  

 

Consult the dealer or an experienced radio/TV technician for help

.

  

 

Modifications not expressly approved by the manufacturer could void the 

user's authority to operate the equipment under FCC rules. 

 

 

 

 

The CE logo indicates that this product has been tested and shown to conform 

with all applicable European Conformity directives. 
 

 
 

 
 
 
 
 
 

Содержание TRI PARALLEL MIXER













Отзывы: