manualshive.com logo in svg

electrifly SR22 Turbo, Инструкция по эксплуатации

Поделиться
Скачать
electrifly SR22 Turbo Скачать руководство пользователя страница 4

4

ADDITIONAL ITEMS REQUIRED

Adhesives and Building Supplies

This is the list of Adhesives and Building Supplies that are 

required to fi nish the Cirrus SR22 ARF:

❏  

1/2 oz. [15g] Thin Pro

™

 CA (GPMR6001)

❏  

1/2 oz. [15g] Thick Pro CA- (GPMR6013)

❏  

Threadlocker thread locking cement (GPMR6060)

❏  

Drill bits: 1/16" [1.6mm], 5/64" [2mm]

❏  

Small metal fi le or rotary tool

❏  

Revell

®

 #1 Light Duty Aluminum Handle Knife w/Blade 

(RMXR6901)

❏  

Revell #11 Light Duty Blades (5) (RMXR6930)

❏  

Medium T-pins (100, HCAR5150)

❏  

Top Flite

®

 MonoKote

®

 sealing iron (TOPR2100) 

❏  

Top Flite Hot Sock

™

 iron cover (TOPR2175)

❏  

220 grit sandpaper

❏  

Panel Line Pen (TOPQ2510)

Optional Supplies and Tools

Here is a list of optional tools that will help you build the 

Cirrus SR22 ARF:

❏  

1/2 oz. [15g] Medium Pro CA+ (GPMR6007)

❏  

2 oz. [57g] spray CA activator (GPMR6035)

❏  

4 oz. [113g] aerosol CA activator (GPMR6034)

❏  

CA applicator tips (HCAR3780)

❏  

CA debonder (GPMR6039)

❏  

Pro 6-minute epoxy (GPMR6045)

❏  

Pro 30-minute epoxy (GPMR6047)

❏  

Epoxy brushes 6, (GPMR8060)

❏  

Mixing sticks (GPMR8055)

❏  

Mixing cups (GPMR8056)

❏  

Pliers with wire cutter (HCAR0630)

❏  

Rotary tool reinforced cut-off wheel (GPMR8020)

❏  

Hobby Heat

™

 micro torch II (HCAR0755)

❏  

Precision Magnetic Prop Balancer (TOPQ5700)

❏  

AccuThrow

™

 Defl ection Gauge (GPMR2405)

❏  

CG Machine

™

 (GPMR2400)

❏  

Hobbico Flexible 18" Ruler Stainless Steel (HCAR0460)

❏  

Top Flite MonoKote heat gun (TOPR2000)

❏  

Hobbico Pin Vise 1/16 Collet w/6 Bits (HCAR0696)

❏  

Great Planes Heat Shrink Tubing 3/8x3" (3) (GPMM1060)

❏  

Woodland Scenics Low Temp Foam Glue Gun 
(WOOU1445)

❏  

Denatured alcohol (for epoxy clean up)

Building Stand

A building stand or cradle comes in handy during the build. 

We use the Robart Super Stand II (ROBP1402) for all our 

projects in R&D, and it can be seen in pictures throughout 
this manual.

IMPORTANT BUILDING NOTES

• When you see the term test fi t in the instructions, it means 

that you should fi rst position the part on the assembly without 
using any glue, then slightly modify or custom fi t the part as 
necessary for the best fi t.

• Whenever the term “glue” is written, you should rely upon 

your experience to decide what type of glue to use. When 
a specifi c type of adhesive works best for that step, the 
instructions will make a recommendation.

• Photos and sketches are placed before the step they refer 

to. Frequently you can study photos in following steps to get 
another view of the same parts.

• The Cirrus SR22 is factory-covered with Top Flite Jet White 

MonoKote fi lm (TOPQ0204). Should repairs ever be required, 
MonoKote can be patched with additional MonoKote 
purchased separately. MonoKote is packaged in six-foot rolls, 
but some hobby shops also sell it by the foot. If only a small 
piece of MonoKote is needed for a minor patch, perhaps a 
fellow modeler would give you some. MonoKote is applied 
with a model airplane covering iron, but in an emergency a 
regular iron could be used. A roll of MonoKote includes full 
instructions for application.

• The stabilizer and wing incidences and engine thrust angles 

have been factory-built into this model. However, some 
technically-minded modelers may wish to check these 
measurements anyway. To view this information visit the web 
site at www.greatplanes.com and click on “Technical Data.” 
Due to manufacturing tolerances which will have little or no 

effect on the way your model will fl y, please expect slight 
deviations between your model and the published values.

Содержание SR22 Turbo

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды