Electra Roman Blinds Скачать руководство пользователя страница 10

Страница: 10 / 16

Step 1 - T

ake a handset or wall

switch that is already
programmed to the blind
motor.

Step 2 -

Press and hold the

program button  of  the
handset or  wall  switch until
the  blind jiggles  (approx
2-3 secs).

Step 3 - Press the progra

button again to unpair the
control

Add/delete controls

Delete a control

Control already

paired

to the

blind

Add a control

Control

to add to

the

blind

memor

Step 1

- Press the prog

ram

button on your handset or
wall switch that already
controls the blind for about
2 seconds until the blind
jiggles. If using a 4 channel
handset, make sure you
have the right channe

ected.

Step 2- Press and hold the
program button of the new
handset or wall switch until
the blind jiggles (approx 1
sec).

Содержание Roman Blinds

















Результаты поиска

Содержание Roman Blinds

Отзывы:

Похожие инструкции для Roman Blinds

Бренды по названию

Популярные бренды

Electra Roman Blinds, Как установить, запрограммировать и эксплуатировать

Результаты поиска

Содержание Roman Blinds

Отзывы:

Похожие инструкции для Roman Blinds

Бренды по названию

Популярные бренды