background image

11

www.elecro.co.uk

EN

G

L

ISH

To avoid inaccurate results when performing this test, it is important to 
refrain from using other high current drawing appliances in the property 
(such as tumble dryer, showers, cooker etc).

A large domestic pool pump of 1-horsepower will draw less than 1-kW in a 
one hour period. The conclusion of the test should prove that for example 
a 6-kW heater and a ½ horsepower pump will draw between 6.3-kW to 
6.5-kW in one hour. It is impossible for an electric heater to waste energy, 
if it is drawing power then that power will be turned into heat that will be 
transferred to the water.

NO LIGHT APPEARS ON THE HEATER WHEN IT IS SWITCHED ’ON’

Possible cause: 

Power failure external to the heater

Remedy:

 Check any fuses, RCD or other switch components installed in 

the supply cable. 

Note: A fuse is fi tted on the digital control circuit board on the inside 
of the enclosure (qualifi ed electricians only).

THE FLOW TUBE DOES NOT FEEL WARM

Due to the high effi

  ciency of your electric heater no warmth should be 

detectable from the fl ow tube of the heater.
The most likely causes of the fl ow tube feeling warm are:-

Possible cause 1: 

The heater has been positioned in direct sunlight.

Possible cause 2:

 An air pocket is trapped inside the heater particularly if 

the tank feels warmer at the highest point of the tank (as air rises).

Q:

 How long will it take to heat my pool? 

A:

  

Assuming no heat losses

, and a heater sized in the ratio 1.5-kW  

 

per 1,000 UK gallons of water (4,545-litres): it will take 2 days of  

 

 

continuous running to raise the temperature of a pool from tap  

 

 

temperature to swimming temperature. Heat loss will slow the heating  

 

process, particularly during periods of cold weather, hence the higher  

 

the water temperature is to be maintained above average ambient air  

 

temperature, the slower the heating process will become.

 
 

The only infl uencing factors are the level of insulation and the location  

 

of the pool with regard to wind shelter.

Содержание IN-LINE+

















Отзывы: