Elba COVO 668/90 Скачать руководство пользователя страница 2

12

TROUBLE SHOOTINGS

CAUT ION: Disconnect the power supply before servicing.

STATUS

CAUSE AND METHOD OF REPAIRING

TOOL

T he power
supply is
d amaged

If the power supply is damaged,please call
technicians to repair.

the

"+" type
Screwdriver
Sharp Pincers

The lamp
works but the
motor does

not run

a) Remove the vane guard and rotate the vane by

hand,If the vane cannot move smoothly, the core
or bearings of the motor may be damaged. In this

case, replace with a new motor.

b) If the motor stops running and has a bad odor

a moment of operation, the motor wires may

burnout. Replace the motor.

c) If the starting wire (yellow) is disengaged from

the condenser, it needs to be rewired.

d) If the condenser is damaged, replace with a new

one.

after

be

"+" type
Screwdriver

The lamp works
but the motor
does not run

a) Take off the filter and check the connection

between air inlet and wind chamber is sealed or
not.

b) Check the connection between air exhaust pipe

and wind chamber leaks oil or not. If"YES, please
fill it up with the varnish or the thinner.

"+" type
Screwdriver

Machine vibration

a) If the motors were not firmly screwed, screw tigh

-ten them up.

b) If the vane is damaged or unbalanced, replace

a new one.

with

"+" type
Screwdriver

Weakness suction

a) The distance is too far between the Cooker Hood

and the Gas Cooker.

b) There are many windows (doors) cause wind con

-vection is too strong.

c) Because of the Cooker Hood is set upon the win

-dow, the best solution is that put one three-ply
board on the back of the Cooker Hood for cover-
ing the hollow of window.

"+" type
Screwdriver

Installation of
the model is tilt

a) Adjust the height of the model where is hang on

the ceiling.

b) If the model tilt forward, lock into the wall with

wood screw again (the screw peep out around 0.5
~1 cm from the wall), or check the screws for fix

-

the model are loose or not.

ing

"+" type
Screwdriver

Bulb does not
light

Just screw off the lamp shade and replace with a new
bulb,then put the lamp shade back.

"+" type
Screwdriver

PDF 

文件使用

 "pdfFactory" 

试用版本创建

 

А

 

 

 

 

 

 

 

 

 

www.fineprint.cn

Содержание COVO 668/90









Отзывы: