Ekinex EK-DB2-TP Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 33

Ekinex EK-DB2-TP Скачать руководство пользователя страница 33

Application manual

Presence detectors KNX EK

-

Dx2

-

TP (x = B, C, D, E)

Release 1.01

-

Update: 05/2014

MAEKDx2TP_EN

© SBS S.p.A.

–

All rights reserved

Page 33

7.2

Warnings

•

Installation, electrical connection, configuration and commissioning of the device can only be
carried out by qualified personnel in compliance with the applicable technical standards and laws
of the respective countries.

•

Opening the housing of the device causes the immediate end of the warranty period

•

In case of tampering, the compliance with the essential requirements of the applicable directives, for
which the device has been certified, is no longer guaranteed

•

ekinex® KNX defective devices must be returned to the manufacturer at the following address:

SBS S.p.A.

Via Circonvallazione s/n

I

-

28010 Miasino (NO)

-

Italy

7.3

Other information

•

This datasheet is aimed at installers, system integrators and planners

•

For further information on the product, please contact the ekinex® technical support at the e

-

mail

address [email protected] or visit the website www.ekinex.com

•

ekinex ® is a registered trademark of SBS S.p.A.

•

KNX®and ETS® are registered trademarks of KNX Association cvba, Brussels

© SBS S.p.A. 2014. The company reserves the right to make changes to this documentation without notice

«
...
31
32
33

Содержание EK-DB2-TP


































Отзывы:

Нет отзывов