GB
- 36 -
The robot lawn mower will now operate in ac-
cordance with the mowing time setting. The batte-
ry charge level is monitored during the work time
and displayed via the battery LED (52). Whenever
the battery charge level drops to 30%, the robot
lawn mower automatically returns to the charging
station (19).
Stopping mowing
1. To bring the robot lawn mower to an immedia-
te stop, press the STOP button (3).
2. Unlock the control panel (2).
3. Press the “HOME / 3” button (64) followed by
the “OK” button (61) to send the robot lawn
mower along the perimeter wire (18) and
back to the charging station (19).
7. Cleaning, maintenance and
ordering spare parts
Hazard!
The equipment must be disconnected from the
power supply (pull out the power plug and switch
o
ff
the equipment by the main switch (7) (OFF)
(Fig. 8) prior to performing any cleaning and
maintenance work.
Caution! Wear work gloves!
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
Do not clean the robot lawn mower with run-
ning water, particularly with high-pressure
water.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment.
•
For best results, clean the robot lawn mower
with a brush or rag.
•
Check the freedom of movement of the bla-
des (10) and the blade plate (11)
•
Use cleaning product for metal or very fine
abrasive paper to clean the charging contacts
on the robot lawn mower (1) and the charging
station (19). Clean them in order ensure effici-
ent charging.
7.2 Maintenance
•
Worn or damaged blades (10) and their fas-
tening screws must always be replaced as a
set.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the equip-
ment for many years to come, all screwed
parts, as well as the wheels and axles, should
be cleaned and lubricated.
•
Keeping your robot lawn mower in good
condition not only ensures a long lifespan
and high performance, but also enables the
equipment to thoroughly cut your grass with
minimal effort.
•
The blades (10) are subject to more wear and
tear than any other component. Therefore,
routinely check the condition of the blades
(10) and make sure that they are tightly fas-
tened. An excessively vibrating robot lawn
mower can indicate that the blades (10) are
damaged or have become deformed from
striking an object. If the blades (10) are worn
or damaged, they must be replaced immedia-
tely.
•
Check the appearance of the cut lawn at re-
gular intervals. The grass will not be cleanly
cut if the blades are not sharp. This can result
in the surface of the lawn drying out easily
and turning brown. It is important therefore to
change the blades regularly in order to obtain
a clean and straight cut.
•
Check the bottom of the robot lawn mower
for dirt at regular intervals. Clean your robot
lawn mower regularly. Remove heavy soiling
immediately.
•
Heavy soiling of the robot lawn mower is
possible in the first weeks of using it for the
first time after a conventional law mower had
previously been used. In these first few weeks
you should check the bottom of your robot
lawn mower more often.
•
Shorten the lawn only in small steps in order
to prevent heavy soiling.
•
There are no other parts inside the equipment
which require maintenance.
7.2.1 Replacing the blades
Only replace the blades with genuine blades, as
this will ensure top performance and safety.
The robot lawn mower is equipped with three bla-
des (10)
fi
tted to a blade plate (11). These blades
(10) have a service life of up to 3 months (if they
do not strike any obstacles). Please replace all
three blades (10) at the same time to ensure that
Anl_GC_RM_500_SPK9.indb 36
Anl_GC_RM_500_SPK9.indb 36
16.02.2021 14:17:33
16.02.2021 14:17:33
Содержание GC-RM 500
Страница 195: ... 195 Anl_GC_RM_500_SPK9 indb 195 Anl_GC_RM_500_SPK9 indb 195 16 02 2021 14 17 55 16 02 2021 14 17 55 ...
Страница 196: ... 196 Anl_GC_RM_500_SPK9 indb 196 Anl_GC_RM_500_SPK9 indb 196 16 02 2021 14 17 55 16 02 2021 14 17 55 ...
Страница 197: ... 197 Anl_GC_RM_500_SPK9 indb 197 Anl_GC_RM_500_SPK9 indb 197 16 02 2021 14 17 55 16 02 2021 14 17 55 ...
Страница 198: ...EH 02 2021 03 Anl_GC_RM_500_SPK9 indb 198 Anl_GC_RM_500_SPK9 indb 198 16 02 2021 14 17 55 16 02 2021 14 17 55 ...