GB
- 17 -
•
With the right couplings it is also possible, of
course, to use a 13 mm (½ “) delivery hose.
The smaller delivery hose results in a lower
delivery rate.
•
During the priming operation, fully open any
shut-off mechanisms (spray nozzles, valves,
etc.) in the pressure line so that the air can
escape without obstruction.
5.4 Electrical connections
•
Connect the appliance to a 230 V ~ 50 Hz
socket-outlet with earthing contact. Minimum
fuse 10 ampere.
•
A built-in thermostat protects the motor from
overloading and blocking. The pump is swit-
ched off automatically by the thermostat if
overheating occurs and is switched on again
automatically after cooling.
6. Operation
•
Install the equipment on a solid and level
surface.
•
Fill the pump housing with water via the water
filler screw (4). Filling the intake line will acce-
lerate the priming process.
•
All the shut-off devices in the discharge line
(spray nozzle, valves etc.) must be fully ope-
ned during intake in order to permit all air to
escape from the intake line.
•
Connect the mains cable.
•
Switch on the equipment with the power
switch (5) - water can be suctioned in for up
to 5 minutes (maximum suction height).
•
After finishing the work, switch off the equip-
ment with the power switch (5).
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
authorized after-sales service or similarly trained
personnel to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
The equipment is almost completely maintenance
free. In order to ensure a long service life, howe-
ver, we recommend that you regularly check and
care for the product.
Danger!
The equipment must be disconnected from the
power supply (pull the power plug) prior to perfor-
ming any maintenance.
8.1 Servicing
•
If the equipment becomes clogged, connect
the discharge line to the water line and dis-
connect the suction hose. Open the water
line. Switch on the equipment several times
for approx. two seconds. This should resolve
the majority of clog-related problems.
•
There are no parts inside the equipment
which require additional maintenance.
8.2 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
Anl_SA_GC_GP_6538_SPK8.indb 17
Anl_SA_GC_GP_6538_SPK8.indb 17
04.04.16 08:37
04.04.16 08:37
Содержание GC-GP 6538
Страница 3: ...3 2 3 4 5 Anl_SA_GC_GP_6538_SPK8 indb 3 Anl_SA_GC_GP_6538_SPK8 indb 3 04 04 16 08 37 04 04 16 08 37...
Страница 30: ...30 Anl_SA_GC_GP_6538_SPK8 indb 30 Anl_SA_GC_GP_6538_SPK8 indb 30 04 04 16 08 37 04 04 16 08 37...
Страница 31: ...31 Anl_SA_GC_GP_6538_SPK8 indb 31 Anl_SA_GC_GP_6538_SPK8 indb 31 04 04 16 08 37 04 04 16 08 37...
Страница 32: ...EH 03 2016 01 Anl_SA_GC_GP_6538_SPK8 indb 32 Anl_SA_GC_GP_6538_SPK8 indb 32 04 04 16 08 37 04 04 16 08 37...
