EINHELL BS315UG, Руководство по эксплуатации

Страница: 21 / 64

the side cover (12) again and secure it with the
fasteners (13).
7.5 Adjusting the blade guide (Fig. 11 -13)
Whenever you change the blade you must reset both
the support bearings (30 + 31) and the guide pins
(28 + 29).
Undo the fasteners (13) and open the left side
cover (12).
7.5.1. Upper support bearing (Fig. 11)
Undo the screw (33).
Move the support bearing (30) so that it is
almost touching the blade (25). There should be
a gap of approx. 0.5 mm.
Re-tighten the screw (33).
7.5.2. Setting the lower support bearing (31)
(Figure 12/13)
Disassemble the saw table (15).
Adjust in the same way that the upper support
bearing was adjusted.
The blade (25) is only supported by the support
bearings (30 + 31) during cutting. When idle the
blade should not touch the ball bearings.
7.5.3. Setting the upper guide bearings (28)
(Figure 11)
Undo the screw (35).
Move the mount (36) of the guide bearings (28)
so that there is a gap of approx. 1 mm between
the front edge of the guide bearings (28) and the
gullet of the blade in front.
Re-tighten the screw (35).
CAUTION! The blade will be rendered useless if
the teeth touch the guide bearings while the
blade is running.
Undo the screws (37)
Move the two guide bearings (28) towards the
blade so that there is a gap of approx. 0.5 mm
between the guide bearings (28) and the blade
(25). (The blade must not jam.)
Re-tighten the screws (37).
Turn the upper blade pulley (8) several times in
a clockwise direction.
Check the setting of the guide bearings (28)
again and re-adjust if necessary.
7.5.4. Setting the lower guide bearings (29)
Figure (12/13)
Disassemble the saw table (15) (see 7.2).
Undo the screw (40)
Move the mount (49) of the guide pins (29) so
that there is a gap of approx. 1 mm between the
front edge of the guide pins (29) and the gullet
of the blade in front.
Re-tighten the screw (40).
CAUTION! The blade will be rendered useless if
the teeth touch the guide pins while the blade is
running.
Undo the screws (38).
Move the guide pins (29) towards the blade so
that there is a gap of max. 0.5 mm between the
guide pins (29) and the blade (25). (The blade
must not jam.)
Re-tighten the Allen screws (38).
Turn the lower blade pulley (7) several times in
a clockwise direction.
Check the setting of the guide pins (29) again
and re-adjust if necessary.
7.6 Adjusting the upper blade guide (11) (Fig.
2/14)
Undo the fixing handle (20).
Turn the adjustment wheel (19) to lower the
blade guide (11) as close as possible to the
workpiece to be cut (the gap should be approx.
2-3 mm).
Re-tighten the fixing handle (20).
Check the setting before each cut and re-adjust
if necessary.
7.7 Adjusting the saw table (15) to 90° (8/15)
Move the upper blade guide (11) to the top.
Undo the fixing handles (18).
Set the angle (d) between the blade (25) and
the table (15).
Tilt the saw table (15) by turning it so that the
angle between it and the blade (25) is precisely
90°.
Re-tighten the fixing handles (18).
Undo the screw (52) of the pointer of the dial
scale (16), set the pointer to exactly 0° and
tighten the screw (52) again.
GB
21
Anleitung BS 315 UG SPK1 02.11.2005 8:49 Uhr Seite 21