11
GB
2. Technical data
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 cm
3
Max. Air Velocity . . . . . . . . . . . . . . . . . . . .ca. 40 m/s
Max. Air Volume . . . . . . . . . . . . . . . . . . . . . .240 m
3
/h
Max. Engine Speed . . . . . . . . . . . . . . . . .11,500 min
-1
Collection Bag . . . . . . . . . . . . . . . . . . . . . . . . .55 Litre
Mulching Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .10:1
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . .700 ml
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.4 kg
Maximum Enquine Performance . . . . . . . .0.8 kW
Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 dB(A)
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . .13.7 m/s
2
3. BLOWER ATTACHMENT ASSEMBLY
INSTRUCTIONS
1. Release the screws (A) and remove the screw (B).
Insert blower tube (C) into the blower housing and
replace screw (B). Tighten screws (A). (Fig. 1A)
2. Insert speed cleaner head (D) to the tube (C). (Fig.
1B)
• HARNESS INSTALLATION
Attach the 2 harness clips to the
2 links in the blower handle.
(Fig. 2)
• VACUUM ATTACHMENT ASSEMBLY
INSTRUCTIONS
To install vacuum bag:
Pull the slide (A) forward and fit bag (B) into the
vacuum housing. (See Fig. 3)
FUEL AND LUBRICATION
•
FUEL
Use regular grade unleaded gasoline mixed with 40:1
custom 2-cycle engine oil for best results.
WARNING
: Never use straight gasoline in your unit.
This will cause permanent engine damage and void
the manufacturer’s warranty for that product. Never
use a fuel mixture that has been stored for over 90
days.
WARNING:
Use only Class I 2-stroke oil suitable for
air-cooled engines.
• MIXING FUEL
Mix the fuel with 2-cycle oil in a suitable container.
Shake the container to ensure that it is properly
mixed.
•
FUEL AND LUBRICATION
• RECOMMENDED FUELS
Some conventional gasolines are being blended with
oxygenates such as alcohol or an ether compound to
meet clean air standards. Your Talon engine is
designed to operate satisfactorily on any gasoline
intended for automotive use including oxygenated
gasolines.
OPERATING INSTRUCTIONS
• STARTING A COLD ENGINE
Fill fuel tank with proper gas and oil mixture. See
Fuel and Lubrication. Set unit on ground so that it
rests on housing feet.
1. Pull the throttle trigger (A). (It will auto lock) Fig.
4A.
2. Prime the carburetor. Pump the primer bulb (C) 10
times (Fig. 4B).
3. Your unit is designed with a 2 position choke (D):
START “
” and RUN “
”. Move choke lever to
START “
” position (Fig. 4C).
4. Grip handle firmly .
5. Pull starter rope out a short way until resistance is
felt (approximately 100mm). Pull starter rope
Gasoline and
Oil Mix 40:1
Fig. 2
Fig. 1A
Fig. 1B
A
B
C
D
C
Fig. 3
B
A
Anleitung BLS 3200 18.01.2005 16:59 Uhr Seite 11
