EINHELL 4300771, Оригинальная инструкция по эксплуатации

Страница: 14 / 20

coincides with the required angle value (in this
connection see also section 7.3).
Re-tighten the locking screw (22).
Cut as described under section 7.1.
7.5 Limiting the cutting depth (Fig. 16)
The cutting depth can be infinitely adjusted using
the screw (34). Undo the knurled nut on the screw
(34) and move the stop for limiting the cutting
depth (35) to the outside. Set the required cutting
depth by tightening or undoing the screw (34) and
then tighten the knurled nut on the screw (34).
Check the adjustment by making a test cut.
7.6 Chip collection box (Fig. 17, 18 / Item 23)
The saw is equipped with a chip collection box (23)
for sawdust and chips. The chip collection box (23)
can be connected to the extractor adaptor (33).
To empty the chip collection box (23), open it as
shown in Fig. 19 and carefully tap it to empty the
contents.
A suitable dust extraction device may also be
connected to the extractor adapter (33).
7.7 Changing the saw blade (Fig. 1, 19 – 22)
Remove the power plug!
Swing the machine head (4) upwards and lock it
in this position using the locking pin (27).
Press the release lever (3) and swing up the saw
blade guard (6) to the point where the recess in
the saw blade guard (6) is above the flange bolt
(39).
Press the saw shaft lock (5) with one hand while
holding the wrench (B) on the flange bolt (39)
with the other.
Firmly press on the saw shaft lock (5) and slowly
rotate the flange bolt (39) in clockwise direction.
The saw shaft lock (5) engages after no more
than one rotation.
Now, using a little more force, slacken the flange
bolt (39) in the clockwise direction.
Undo the flange bolt (39) and remove it and them
take off the outer flange (40).
Take the saw blade (7) off the inner flange and
pull it out downwards.
Carefully clean the flange bolt (39), outer flange
(40) and inner flange.
Fit and fasten the new saw blade (7) in reverse
order.
Important. The cutting angle of the teeth, in other
words the direction of rotation of the saw blade
(7) must coincide with the direction of the arrow
on the housing.
Check to make sure that all safety devices are
properly mounted and in good working condition
before you begin working with the saw again.
Important. Every time that you change the saw
blade, check to see that it spins freely in the table
insert (12) in both perpendicular and 45° angle
settings.
Important. The saw blade (7) must be changed
and aligned correctly.
7.8 Storage compartment for spare saw blade
(Fig. 23 / Item 28)
The saw is equipped with a storage compartment (28)
for a spare saw blade. To open the storage
compartment (28), pull the locking knob (29) on the
rear of the saw while pulling the storage compartment
(28) out at the same time.
7.9 Using the laser (Fig. 24, 25 / Item 21)
To switch on:
Move the laser ON/OFF switch (42)
into the “I” position to switch on the laser (21). A laser
line is projected on to the workpiece you wish to
machine, providing an exact guide for the cut.
To switch off: Move the laser ON/OFF switch (42)
into the “0” position.
Adjusting the laser: Undoing the screws (41)
slightly allows the laser to be adjusted if necessary.
Tighten the screws again after you have completed
the adjustment work. Important. Never look directly
into the LED light!
Replacing the battery: Ensure that laser (21) is
switched off. Remove the battery compartment cover
(43). Remove the spent batteries and replace them
with new ones (2 x 1.5 V type R02, LR 03 Micro,
AAA). Check that the battery terminals are positioned
correctly. Close the battery compartment again.
7.10 Transport (Fig. 1 – 3)
Tighten the locking grip (14) to lock the turntable
(17).
Press the release lever (3), push the machine
head (4) to the rear and lock it with the locking
bolt (27). The saw is now locked in its lower
position.
Secure the drag function of the saw in its rear
position using the fixing screw for the drag guide
(25).
Carry the machine using the fixed saw bench (18).
Follow the instructions set out in point 6.2 to erect
the machine again.
7.11 Battery disposal
Recycle the packaging. Ensure that you sort the
materials for recycling. Do not dispose of batteries in
household waste. All consumers have a duty to
dispose of batteries properly at the appropriate
collection points. Send your spent batteries to iSC
GmbH, Eschenstrasse 6 in D-94405 Landau. You can
GB
14
Anleitung_RT_SM_430_SPK7:_ 22.06.2010 15:47 Uhr Seite 14