GB
- 8 -
Warning!
Do not press the ON/OFF switch any
more if the protective circuit has actuated. This
may damage the battery.
1. Remove the battery pack (4) from the handle,
pressing the pushlock buttons (5) on the left
and right sides to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(8) into the mains socket outlet. The green
LED will then begin to
fl
ash.
3. Insert the battery pack (4) into the battery
charger (8).
4. In section 10 „Charger indicator“ you will
fi
nd
a table with an explanation of the LED indica-
tor on the charger.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact with the char-
ging contacts in the battery charger (8).
If the battery still fails to become charged, please
return
•
the charger and charging adapter
•
the battery pack
to our Customer Service Department.
To ensure that the LI battery pack provides
long service you should take care to recharge
it promptly. You must recharge the battery pack
when you notice that the power of the cordless
screwdriver drops.
6.2 Torque setting (Fig. 4 / Item 1)
The cordless screwdriver is
fi
tted with a mechani-
cal torque selector.
The torque for a speci
fi
c size of screw is selected
with the set-collar (1). The correct torque depends
on several factors:
•
on the type and hardness of material in ques-
tion
•
on the type and length screws used
•
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important! The tool must be at a standstill when
you set the torque with the setting ring.
6.3 Drilling (Fig. 4 / Item 1)
For drilling purposes, move the set-collar to the
last step „Drill“. In this setting the slip clutch is in-
active. The maximum torque is available in drilling
mode.
6.4 Forward/Reverse switch (Fig. 5 / Item 2)
With the slide switch above the On/O
ff
switch you
can select the direction of rotation of the battery-
powered drill/screwdriver and secure it against
being switched on accidentally. You can choose
between clockwise and anticlockwise rotation. To
avoid causing damage to the gearing it is advisa-
ble to change the direction of rotation only when
the tool is at a standstill. The On/O
ff
switch is blo-
cked when the slide switch is in centre position.
6.5 On/O
ff
switch (Fig. 5 / Item 3)
In
fi
nitely variable speed control is possible with
the On/O
ff
switch. The further you press the
switch, the higher the speed of the battery-powe-
red drill/screwdriver.
6.6 LED lamp (Fig. 5/Item 9)
The LED lamp (9) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED lamp (9) will be lit au-
tomatically as soon as you press the ON/OFF
switch (3).
6.7 Battery capacity indicator (Fig. 5/Item. 10)
Push the ON/OFF switch (3). The battery capacity
indicator (10) indicates the charge state of the
battery on 3 LEDs.
All LEDs are lit:
The battery is fully charged.
2 LEDs are lit:
The battery has an adequate remaining charge.
1 LED:
The battery is discharged, it requires charging.
6.8 Changing the tool (Fig. 6)
Warning!
Set the changeover switch (2) to its
centre position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
•
The cordless screwdriver is fitted with a
quick-action chuck (7) with an automatic
spindle stop.
•
Open the chuck (7). The chuck opening (a)
must be large enough to hold the tool (drill bit
or screwdriver bit).
•
Select the suitable tool. Push the tool as far
as possible into the chuck opening (a).
Anl_TC-CD_12-2_Li_SPK7.indb 8
Anl_TC-CD_12-2_Li_SPK7.indb 8
07.04.2017 08:35:26
07.04.2017 08:35:26
