GB
- 18 -
6.3 Fitting the transport handle (9)
Screw the transport handle (9) to the compressor
as shown in
fi
gures 7 to 8.
6.4 Fitting the air
fi
lter (1)
Use a screwdriver to remove the transportation
cover from the air
fi
lter connection. Screw in the
supplied air
fi
lter (Fig. 9).
6.5 Mains connection
•
The motor is fitted with an overload switch
(Fig. 3/Item 15). If the compressor overloads,
the overload switch will switch off the equip-
ment automatically to protect the compressor
from overheating. If the overload switch trig-
gers, switch off the compressor using the ON/
OFF switch (8) and wait until the compressor
cools down. Then press the overload switch
(15) and restart the compressor.
•
Long supply cables, extensions, cable reels
etc. cause a drop in voltage and can impede
motor start-up.
•
At low temperatures below +5° C, sluggish-
ness may make starting difficult or impossib-
le.
6.6 On/O
ff
switch (8)
To switch on the compressor, pull out the On/O
ff
switch (8).
To switch o
ff
the compressor, press the On/O
ff
switch (8) in again. (Fig. 2)
6.7 Adjusting the pressure:(Fig. 1.2)
•
You can adjust the pressure on the pressure
gauge (6) using the pressure regulator (7).
•
The set pressure can be taken from the quick-
lock coupling (5).
6.8 Setting the pressure switch
The pressure switch is set at the factory.
Cut-in pressure approx. 6 bar
Cut-out pressure approx. 8 bar
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Disconnect the power plug before doing any
cleaning and maintenance work!
Warning!
Wait until the compressor has completely
cooled down. Risk of burns!
Warning!
Always depressurize the tank before carrying
out any cleaning and maintenance work.
Warning!
After use, always switch o
ff
the equipment
immediately and pull out the power plug.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
•
You must disconnect the hose and any
spraying tools from the compressor before
cleaning. Do not clean the compressor with
water, solvents or the like.
8.2 Condensed water (Fig. 1)
Note:
To ensure a long service life of the pressure
vessel (2), drain o
ff
the condensed water by ope-
ning the drain screw (11) each time after using.
Check the pressure tank for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure
tank. If you discover any damage, please contact
the customer service workshop.
8.3 Safety valve (10)
The safety valve has been set for the highest per-
mitted pressure of the pressure tank.It is prohibi-
ted to adjust the safety valve or remove its seal.
Anl_TE_AC_50_Silent_SPK9.indb 18
Anl_TE_AC_50_Silent_SPK9.indb 18
15.07.2020 13:18:51
15.07.2020 13:18:51
Содержание 40.206.20
Страница 118: ...GR 118 Anl_TE_AC_50_Silent_SPK9 indb 118 Anl_TE_AC_50_Silent_SPK9 indb 118 15 07 2020 13 19 30 15 07 2020 13 19 30...
Страница 128: ...128 Anl_TE_AC_50_Silent_SPK9 indb 128 Anl_TE_AC_50_Silent_SPK9 indb 128 15 07 2020 13 19 32 15 07 2020 13 19 32...
Страница 129: ...129 Anl_TE_AC_50_Silent_SPK9 indb 129 Anl_TE_AC_50_Silent_SPK9 indb 129 15 07 2020 13 19 32 15 07 2020 13 19 32...
