GB
- 18 -
5.1 Fitting the blower tube (Fig. 3a/b)
Plug the blower tube onto the motor unit. The
groove (A) must be pushed into the guide (B)
when you do this. Turn the blower tube to the right
to secure it in its
fi
nal position on the motor unit.
Caution! The tube must be turned as far as it will
go to make sure it is
fi
rmly secured in position.
5.2 Fitting the battery (Fig. 4)
Important! Before
fi
tting the battery you must
always set the On/O
ff
slide switch to OFF (see
section 6.1).
Press the pushlock button of the battery pack as
shown in Fig. 4 and push the battery pack into the
mount provided. When the battery pack is posi-
tioned as in Fig. 4, make sure that the pushlock
button latches in place! To remove the battery
pack, proceed in reverse order.
5.3 Charging the battery (Fig. 5)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to blink.
3. Insert the battery pack into the charger.
4. In section 7. „Charger indicator“ you will
fi
nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and
fi
res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.4 Battery capacity indicator (Fig. 6)
Press the button for the battery capacity indicator
(A). The battery capacity indicator (B) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED
fl
ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
5.5 Fitting the roof guttering cleaning set
(only GP-LB 18/200 Li GK)
The roof guttering cleaning set consists of a con-
nection adapter, three extension tubes and a
fi
nal
bend.
Fig. 7: Screw the connection adapter (Item 5) onto
an extension tube (Item 6).
Fig. 8/8a: Depending on your requirements, screw
on more extension tubes (Item 6) or the
fi
nal bend
(Item 7).
Fig. 9/9a: Plug the connection adapter (Item 5)
onto the blower tube (Item 1). The groove (A)
must be pushed into the guide (B) when you
do this. By turning to the right, the connection
adapter will be secured on the blower tube upon
reaching its
fi
nal position.
Anl_GP_LB_18_200_Li_GK_SPK13.indb 18
Anl_GP_LB_18_200_Li_GK_SPK13.indb 18
20.07.2021 14:03:56
20.07.2021 14:03:56
