EINHELL 34.242.03, Оригинальная инструкция по эксплуатации

Страница: 26 / 62

GB
- 26 -
them if necessary.
•
Carry out a test run on a small area which is
not very visible to check that brushing does
not damage the surface.
•
The surface to be cleaned must be free of ob-
jects such as stones, twigs, etc. These could
be flung up by the rotating brush or scratch
the surface.
•
Lift the equipment 1-2 centimeters off the
ground when you switch it on, but only until it
has reached full speed. Take care when doing
so in order to prevent injuries.
•
Never switch on the equipment while it is
tilted or while it is lifted for any other purpose
than for reaching the full speed – risk of injury!
•
Never use the equipment for too long at any
one point.
•
We recommend wet cleaning. Only use clean
water without any additives whatsoever.
•
Keep your hands and feet away from the rota-
ting brush.
•
Only insert the battery just before you start
your work and remove it again when you have
finished.
6.1 Changeover switch (Fig. 18)
Note:
•
Using the changeover switch you can select
the direction of rotation of the equipment and
lock it so that it cannot be switched on acci-
dentally. You can select between forward and
reverse rotation. Forward is the standard di-
rection of rotation, with which the equipment
has the most power.
•
Hold the equipment firmly by the handle and
additional handle and make sure you have a
steady standing position.
•
To avoid causing damage to the equipment,
the direction of rotation must only be changed
when the equipment is at a standstill.
a) Forward (standard direction of rotation): Slide
switch on left (V) pressed - the equipment
pulls away from you.
b) Safety- lock-o ff : Slide switch in the middle
position (as shown) - On/O ff switch blocked
c) Reverse: Slide switch on right (R) pressed -
the equipment moves towards you.
6.2 On/O ff switch (Fig. 15 / Item 3)
a) Switching on
When you press the On/O ff switch, the brush
rotates.
b) Switching o ff
When you release the On/O ff switch, the
equipment switches o ff and the brush comes
to a standstill.
6.3 Speed controller (Fig. 18 / Item 4)
To set the speed of the brush, turn the speed con-
troller (min = lowest / max = highest). This allows
the speed to be adjusted to the particular surface
being cleaned. The numbers 1 – 5 marked on the
speed controller are provided to indicate the set
speed more clearly.
6.4 Operation
Note: Worn or frayed brushes should be replaced
in good time. Replace the brush as soon as its
diameter is less than approx. 95 mm. A brush dia-
meter of any less can lead to damage.
Important! If the permissible input current is ex-
ceeded (e.g. by pressing too strongly), the equip-
ment switches o ff automatically and must be swit-
ched on again by pressing the On/O ff switch.
6.4.1 Cleaning in general (not applicable to
section “6.4.5 Brushing arti fi cial turf”)
1. Place the brush evenly on the surface.
2. Set the working height to the one which is
most comfortable for you (see section 5.3).
The splash guard (Fig. 1 / Item 14) must just
clear the ground on both sides.
3. Select the correct direction of rotation (see
section 6.1) for the surface you want to clean
(observe sections 6.4.2 – 6.4.4).
4. To achieve top cleaning results quickly, we re-
commend wet cleaning. Open the water inlet.
5. Lift the equipment 1-2 centimeters and switch
on the equipment (see section 6.2).
6. Set the desired speed (from slow to fast) (see
section 6.3). Wait until the full speed has been
reached and then place the brush on the sur-
face to be cleaned.
7. Guide the brush slowly and in lines, similar to
a broom, over the surface. Only apply a small
amount of pressure at fi rst and then increase
it little by little.
6.4.2 Cleaning wood, composite materials
(BPC/WPC)
Warning! Use only the SOFT brush to do this (to
fi t the brush, see section 5.5). All other available
brushes are made of hard material and can da-
mage the surface.
•
Always clean the boards or wooden elements
in a longitudinal direction (along the grain).
•
Actuate the left side (Fig. 18 / Item V) of the
changeover switch (forward). The equipment
will pull away from you (standard direction of
Anl_Picobella_SPK7.indb 26 Anl_Picobella_SPK7.indb 26 19.11.2019 09:17:08 19.11.2019 09:17:08