EINHELL 34.105.91, Инструкция по применению

Страница: 11 / 44

GB
11
Service Center or a specialist workshop.
Keep the tool in a dry place out of children’s
reach.
When the tool is not being used, store it so that
the blades cannot be touched accidentally.
Take care not to overload the tool and do not use
it on jobs for which it is not intended.
The tool requires regular inspection and
maintenance. Always replace damaged blades in
pairs. If the tool suffers any damage from impact
(falling on hard ground etc.), have it checked
immediately by a specialist.
Look after your tool carefully. Keep it clean and
sharp to ensure efficient and safe cutting. Follow
the maintenance and cleaning instructions.
4. Important information
The battery pack supplied with the tool is not
charged. The battery pack has to be charged
before you use the tool for the first time.
Charge the battery pack with the charger
supplied. Do not use the supplied charger to
charge other items of equipment.
The battery pack does not reach its maximum
capacity until it has been charged and
discharged approximately five times.
NC battery packs lose their charge even when
they are not being used. Regular charging is
therefore recommended.
Please check the data marked on the rating plate
of the battery charger. Connect the battery
charger only to an identical mains supply to that
on the rating plate.
In heavy use the battery pack will become warm.
Allow it to cool to room temperature before
commencing with the charging.
Never throw old batteries in the fire. Risk of
explosion!
Used and defective batteries do not belong in the
refuse bin. Think of the environment - cadmium
is toxic. For proper disposal of used and
defective batteries, send them postage-paid to
the ISC company or take them to a special
collecting station in your area. Ask at your local
council offices for the nearest used battery
collecting station.
Protect the battery charger and cable from
damage and sharp edges. Damaged cables are
to be replaced without delay by an electrician.
5. Proper use
The AGSS 18 is designed for cutting lawns, small
areas of grass, bushes and small hedges in private
and hobby gardens.
Tools for private and hobby gardens are not suitable
for use in public facilities, parks and sport centers,
along roadways, on farms or in the forestry sector.
For the tool to be used properly it is imperative to
follow the instructions set out in the manufacturer’s
directions for use.
Important! It is prohibited to use the tool to chop
material for composting because of the potential
danger to persons and property.
6. Technical data
Cutting width of the grass cutter: 85 mm
Cutting length of the shrub cutter: 160 mm
Running time max.: approx. 120 min.
Battery pack: 18 V / 1500 mAh
Charging time: 7-9 h
Battery charger:
Voltage: 230 V ~ 50 Hz
Rated voltage output: 24 V DC
Rated current: 500 mA
Sound power level: 89 dB(A)
Vibration aw: 2,33 m/s 2
The noise level of this power tool is measured accor-
ding to ISO 3744, NFS 31-031 (84/538/EWG). Noise
level at work area can eceed 85 dB (A). In that case
operators should protect themselves against da-
mage to hearing. The vibrations are measured
according ISO 5349.
7. Starting up
7.1 Charging the battery pack (Figure 1, 3)
The charging station can be used as a wall
holder.
Connect the charger to the charging station
(Figure 3 / Item 3).
Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Plug the battery charger in a socket-
outlet. The green LED (Figure 3 / Item 1) comes
on to indicate that charging voltage is available.
Place the tool in the charging station. The red
LED (Figure 3 / Item 2) comes on to indicate that
the battery is being charged. An empty battery
pack requires a maximum charging period of 6
hours. The temperature of the battery pack may
rise slightly during the charging operation. This is
normal.
The red LED (Figure 3 / Item 2) and the green
LED (Figure 3 / Item 1) both come on to indicate
Anleitung AGSS 18 11.11.2003 10:22 Uhr Seite 11