Always push the workpiece through to the end of
the splitter (5).
The offcut piece remains on the saw table (1)
until the blade (4) is back in its position of rest.
Secure long workpieces against falling off at the
end of the cut (e.g. with a roller stand etc.) .
8.1.2. Cutting narrow workpieces (Fig. 19)
Be sure
to use a push stick (3) when making
longitudinal cuts in workpieces smaller than 120
mm in width. A push block is supplied with the
saw!
Replace a worn or damaged push stick
immediately.
8.1.3. Cutting extremely narrow workpieces
(Fig. 20)
Be sure
to use a push block when making
longitudinal cuts in very narrow workpieces with
a width of 30 mm and less.
The low guide face of the parallel stop is best
used in this case.
There is no push block supplied with the
saw! (Available from your specialist dealer)
Replace the push block without delay when it
becomes worn.
8.1.4. Making bevel cuts (Fig. 14/21)
Bevel cuts must always be used using the parallel
stop (7).
Set the blade (4) to the desired angle. (See 7.5.)
Set the parallel stop (7) in accordance with the
workpiece width and height (see 7.3.1)
Carry out the cut in accordance with the
workpiece width (see 8.1.1., 8.1.2 and 8.1.3.)
8.1.5. Making cross cuts (Fig. 22)
Slide the cross stop (21) into one of the grooves
(21) in the table and adjust to the required angle.
(See 8.4.) If you also want to tilt the blade (4),
use the groove (21) which prevents your hand
and the cross stop from making contact with the
blade guard.
Press the workpiece firmly against the cross stop
(14).
Switch on the saw.
Push the cross stop (14) and the workpiece
toward the blade in order to make the cut.
Important:
Always hold the guided part of the
workpiece. Never hold the part which is to be
cut off.
Push the cross stop (14) forward until the
workpiece is cut all the way through.
Switch off the saw again. Do not remove the
offcut until the blade has stopped rotating.
9. Maintenance
Important!
Pull out the power plug first.
Remove dust and dirt regularly from the
machine. Cleaning is best carried out with a fine
brush or a cloth.
Never use caustic agents to clean plastic parts.
10. Ordering replacement parts
Please provide the following information on all orders
for replacement parts:
Model/type of device
Article number of the device
ID number of device
Number of the required replacement part
For our latest prices and information please go to
www.isc-gmbh.info
GB
25
Anleitung_TKS_1500_Eco_SPK1:_ 21.12.2010 13:24 Uhr Seite 25
Содержание 1500 ECO
