Eiki Conference LC-WUL100, Руководство по обслуживанию

Страница: 42 / 162

-42-
Electrical Adjustment
v
Component Auto calibration
Input mode Video mode (Input 2 -Component)
Input signal 100% color bar signal (480i)
100% color bar signal (480p)
100% color bar signal (720p)
100% color bar signal (1080i)
1. Enter the service mode.
2. At first, input the 100% color bar signal (480i).
3. Select Group "
200
", No. "
72
" and set data value
to "
0
". Select Group "
200
", No. "
71
" and set data
value to "
1
".
4. Select Group "
260
", No. "
0
" and set data value "
0
" to
"
1
".
The projector begins auto-calibration and then "OK"
will appear on the screen.
5. Select Group "
200
", No. "
71
" and set data value
to "
0
".
6. Select Group "
260
", No. "
0
" and set data value "
0
"
to "
1
".
The projector begins auto-calibration and then "OK"
will appear on the screen.
7. Change another input signal and take steps 3 - 6 again.
8. Select Group "
200
", No. "
71
" and set data value to
"
1
". Select Group "
200
", No. "
72
" and set data value
to "
1
".
b
Video Auto calibration
Input mode Video mode (Input 3 Video)
Input signal 100% color bar composite video signal
1. Enter the service mode.
2. To start the auto-calibration for composite-video
adjustment, select Group " 260 ", No. " 0 ", and then
change data value " 0 " to " 1 ".
After the auto-calibration completed, "OK" will appear
on the screen.
Adjustments item no. [3] to [5] are carried out at the
spare parts shipment in the factory, therefore they are
not required when the main board is replaced with
new one.
x
Fan Voltages adjustment
Equipment Digital voltmeter
1. Enter the service mode.
2. Adjust the voltage on each test point by changing the
data values of the Group - No.
Group No. Fan Test Point Adjustment value
250 - 0 FN909 TPFN11 4.5 +0.1 -0Vdc
250 - 1 FN909 TPFN11 13.8 +0 -0.1Vdc
250 - 2 FN906 TPFN6 4.5 +0.1 -0Vdc
250 - 3 FN906 TPFN6 13.8 +0 -0.1Vdc
250 - 4 FN904 TPFN4 4.5 +0.1 -0Vdc
250 - 5 FN904 TPFN4 13.8 +0 -0.1Vdc
250 - 6 FN902 TPFN2 4.5 +0.1 -0Vdc
250 - 7 FN902 TPFN2 13.8 +0 -0.1Vdc
250 - 8 FN901 TPFN1 4.5 +0.1 -0Vdc
250 - 9 FN901 TPFN1 13.8 +0 -0.1Vdc
250 - 10 FN903 TPFN3 4.5 +0.1 -0Vdc
250 - 11 FN903 TPFN3 13.8 +0 -0.1Vdc
250 - 12 FN905 TPFN5 4.5 +0.1 -0Vdc
250 - 13 FN905 TPFN5 13.8 +0 -0.1Vdc
5. Select Group "
260
", No. "
0
" and set data value "
0
"
to "
1
".
The projector begins auto-calibration for SUB and
then "OK" will appear on the screen.
6. Select Group "
200
", No. "
70
" and set data value
to "
0
". Select Group "
200
", No. "
72
" and set data
value to "
1
".
After replacing the Power Board, perform the Output
voltage adjustment as follows.
1. Connect a digital voltmeter to pins 2 (-) and 1 (+) of
K6a
.
2. Adjust the voltage by using VR601 as following.
AC Input Reading
230V 370V ±2V
Caution:
Be sure to connect the lamp when taking this adjust-
ment.
* This adjustment is not required even if the power board
is replaced because this adjustment is carried out be-
fore parts shipment.
z
Output Voltage adjustment
c
PC Auto calibration
Input mode Computer mode (Input 1 RGB)
Input signal 16-step gray scale computer signal
1. Enter the service mode.
2. Select Group " 200 ", No. " 70 " and set data value to
" 0 ". Select Group " 200 ", No. " 72 " and set data value
to " 0 ".
3. Select Group " 260 ", No. " 0 " and set data value " 0 "
to " 1 ".
The projector begins auto-calibration for MAIN and
then "OK" will appear on the screen.
4. Select Group " 200 ", No. " 70 " and set data value
to " 1 ".