manualshive.com logo in svg

Egholm City Ranger 2200, Руководство оператора, Страница: 21 / 28

Поделиться
Скачать
Egholm City Ranger 2200 Скачать руководство пользователя страница 21

1

2

21

 

Service and maintenance

3.2 Maintenance

Incomplete seal on turbine:

The seal will become uneven or damaged over time and 
must be changed. (Picture 1)

Imbalance/vibration in the hopper:

Under certain circumstances, imbalance/vibration can 
occur in the hopper. This may be caused by dried-on dirt 
in the turbine.

Standing under the hopper when it is raised.

If you need to stand under a raised hopper during cleaning 
or maintenance, follow the procedure below:

1. Lift the hopper to its highest position and then tip it.

2. Stop the machine and engage the handbrake.

3. The hopper’s own weight will hold it in position. 
(Picture 2)

NB!

The hopper has a break valve fitted to ensure the hopper 
continues to lift to its full height if a hydraulic hose breaks.

3.3 Troubleshooting

The hopper suction does not work. Possible causes:

1. The hopper is full.

2. The grass filter is blocked and must be cleaned. (See 
section 3.1 Cleaning)

Replace the seal on the turbine

Hopper is tipped as far as it can

Operator’s Manual City Ranger 2200 Grass Collector

Service and maintenance

Содержание City Ranger 2200





























Отзывы:

Нет отзывов